Results 1 to 8 of 8
Thread: Boatmate trailer brakes problem
-
09-11-2013, 11:28 AM #1
Boatmate trailer brakes problem
Hey guys, I was wondering if any of you know what size bolt I need to reattach one of the brake lines to the left trailer side wheel brake. I walked by it the other day and saw that something was hanging. Got under there and it was the brake line. Here are two pics to help describe what I'm talking about better:
Left:
Right:
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
09-11-2013, 11:29 AM #2
Boatmate trailer brakes problem
BTW this is a single axle trailer 2010/2011
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
09-11-2013, 11:37 AM #3
That is a special Banjo bolt that the fluid actually runs through. Since you're going to have to bleed the brakes anyway, you may want to just take the other one off and bring it in with you as a sample.
So when is this "old enough to know better" supposed to kick in?
2001 MobiusV - Slightly Modified...
-
09-11-2013, 12:56 PM #4
-
09-11-2013, 02:43 PM #5
Make sure you get the copper washers that go on each side of the square metal block.
jy
-
09-11-2013, 03:03 PM #6
A note on the copper washers, I just replaced a broken brake line on my single axle trailer. I went to three diffrent auto parts retailers and was unable to find that size washer. I then went to a brake shop and was told the washer seems to be a custom size as he had never seen one like it before. Now I'm not a car guy by any means, but I thought it strange I couldn't find the proper size anywhere I looked. I ended up ordering the parts from www.boatmateparts.com. Stupid little washers cost $4/each. If you have trouble finding the right size bolt, I would email Jerry at boatmate.
Jr.
'08 Outback V
-
09-11-2013, 03:30 PM #7
Boatmate trailer brakes problem
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
09-11-2013, 05:22 PM #8
[email protected] He was very helpful with sending part numbers for items that can't be found on the parts site.
Good LuckJr.
'08 Outback V