Results 21 to 30 of 30
Thread: Sloppy Swim Platform - '13 Mojo
-
09-04-2013, 03:41 PM #21
For those with an LSV, see page 8 of the thread below for a simple solution to this issue. I put a lock washer in the gap at the top and it eliminates the rattle. This may or may not work for you depending on the size of the gap.
https://forum.moomba.com/showthread....asher+platformAl
2006 Mobius LSV
-
05-30-2014, 09:34 PM #22
After about a year the set screws on mine ('13) are wearing dangerously close to going through the bracket. Anyone else see this?
'06 Outback - Gone but not forgotten
'13 Mojo
-
05-30-2014, 11:46 PM #23
Sloppy Swim Platform - '13 Mojo
Work with your dealership. I had mine replaced with the 14 platform brackets for around 250 out of pocket. Normally would run over a grand. Dealership ate the labor and gel work and SC helped with the bracket exchange. The new brackets are stainless with no slop at all.
Sent from my iPhone using TapatalkShane
2016 Supra SE
EXILED
6 XM9 Tower
6 Wetsounds XS650 Cabin
1 EXILE BIG 12 DVC 2000 watt in a ported box
1 XM 15.4
XI 1500.1
2 MX 30.2
Wetsounds 420 EQ
EXILE Blue tooth EXBT4
Blue LEDs
-
05-31-2014, 09:36 AM #24
Sloppy Swim Platform - '13 Mojo
I'm looking at doing the same thing, problem is my dealer doesn't do gel work so I'd have to take it somewhere for hat part of the work. I'm sure I'll be in a little more $ to get mine done.
I did replace the hardware, helps some.
Sent from my iPhone using Tapatalk2022 Moomba Mojo
2013 Moomba Mojo 2.5 (sold)
Tow - 2019 Ford F150 Ecoboost
-
05-31-2014, 11:18 AM #25
I think I might have been one of the first to do this this year. I was able to get SC to work with me and my dealer as part of a warranty. My brackets where really worn down plus I had longer screws installed that where all bent.
Very worth every dollar.Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]
-
07-18-2014, 12:44 AM #26
Can anyone post a picture(s) with the old and new versions side by side?
2012 Mojo2.5
Ballast:
1100 surf side
400 goofy side
500 under floor
725 IBS
260 bow floor
(The more spotters the better)
Acme1235
-
07-18-2014, 11:45 AM #27
I don't have any of the 13 brackets pictured from my Mojo.
Here is my 08 LSV with the same brackets they used up through 12 model year.
New 14 style after they replaced the factory 13s. Honestly you can't see any gell work or anything. Dealer said its almost a direct bolt up. They have to redril the platform mounts under the swim deck. They used RTV to seal the old screw holes.
Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]
-
07-18-2014, 12:59 PM #28
I don't have any good pics, but I'm pretty sure my '13 OBV brackets look pretty much the same as Mike's pics of his old '08....
Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...
-
07-18-2014, 01:16 PM #29
New brackets were not introduced until '14, unless you have had a warranty claim done since. '13 brackets were similar to Mike's post except they added the set screw.
-
07-20-2014, 01:29 AM #30
Thanks, mine seems to be holding in there but we dont get the hours on it that i'd like. I'm going to speak with my dealer and see how big a deal it is...
2012 Mojo2.5
Ballast:
1100 surf side
400 goofy side
500 under floor
725 IBS
260 bow floor
(The more spotters the better)
Acme1235