Results 11 to 20 of 25
Thread: LED Light Project
-
02-14-2013, 11:53 PM #11Senior Member
- Join Date
- Aug 2011
- Posts
- 2,522
Re: LED Light Project
Inspiration..
https://www.youtube.com/watch?v=MX1O...e_gdata_player
Sent from my Nexus 4 using Tapatalk 2http://www.instgram.com/jlyons30
2002 Moomba Mobius LSV - Sold
2006 Moomba Mobius LSV - Sold
2017 Moomba Craz - Enzos, Lead
-
02-15-2013, 12:39 AM #12
LED Light Project
I'm not looking at doing anything in the water. just wanna throw some strips in the interior along the sides, bow, foot well where sub is and maybe the drink holders
sent from my home phoneJason
Go Hard or Go Home.......it's MOOMBA time!!
2009 Moomba Mobius LSV
-
02-15-2013, 02:08 AM #13
Re: LED Light Project
Oznium seemed to make a pretty good strip. I've been happy with mine but haven't looked at anything else.
Dusty replaced our courtesy lights with single matching bulbs and tied it all into courtesy. Simple but effective.
Sent from my DROID RAZR using Tapatalk 22016 Moomba Mojo
2006 Supra 24SSV - Traded
-
02-15-2013, 09:02 AM #14
-
02-15-2013, 10:30 AM #15Junior Member
- Join Date
- Jan 2013
- Posts
- 10
KG, do you have a supplier for the courtesy light replacement led's? I want to pull those dingy bulbs and getting something that is brighter.
Bill D.
-
02-15-2013, 10:55 AM #16
LED Light Project
David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
02-15-2013, 10:57 AM #17
times 2 ...........
A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
02-15-2013, 11:07 AM #18
We used the prewired super flux. Just spliced the factory wire and put these in its place.
http://www.oznium.com/prewired-superflux
Some pics from ours that got archived
"I've had a few PM's from people asking about the LED's and what all we did, so I figured I would just post my process. Everything is powered by the factory courtesy light wiring, off of that switch, even what we added. For above the cup-holders, the Supras already had a small 3 LED unit above them, I removed this and just replaced with flexible strip. Wired directly in place of the old. Same for rear lockers, behind the driver seat locker, and the rear transom light. The only change to the wiring for the lockers was the ground wire was ran to the switch, and another ground from the switch back to the LED so when closed, the ground was interrupted and they shut off. "Last edited by KG's Supra24; 02-15-2013 at 11:15 AM.
2016 Moomba Mojo
2006 Supra 24SSV - Traded
-
02-15-2013, 11:17 AM #19
I can't remember if there are 1 or 2 superflux in each of the factory housings in the floor. Dusty, remember?
If you are considering doing RGB at all .... just do it up front.2016 Moomba Mojo
2006 Supra 24SSV - Traded
-
02-15-2013, 11:29 AM #20
LED Light Project
so KG your entire LED system is on/off by the acc switch. you have no remotes or power sources etc. just the lights and the pig tail connectors?
sent from my home phoneJason
Go Hard or Go Home.......it's MOOMBA time!!
2009 Moomba Mobius LSV