Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19
  1. #11
    Join Date
    Feb 2012
    Location
    St. Albert, Alberta, Canada
    Posts
    170

    Default


    So I got my valve installed.

    Moved my pumps as well.


    Sent from my iPhone using Tapatalk
    2010 MOOMBA LSV
    340 CAT
    ACME 1235
    3100#'s




  2. #12
    Join Date
    Nov 2003
    Location
    Land O Lakes, Florida
    Posts
    6,377

    Default

    looking good so far, make sure to report how it all works
    Hey, Its Moomba time

    Its all about the dash - enjoy the dash, as that is your time between the dates
    13 Mobius LSV-sold
    08 Mobius LSV-sold
    03 Mobius LSV-sold
    life is about finding the balance between being a responsible adult and staying young at heart

  3. #13

    Default

    Looks good! If you can, try to tilt that pump mounted to the panel so the pump head (where the hoses attach) is a little lower. That will help extend the life of the pump.

    The Y Valve is a great way to add a lot of control, without the expense of additional pumps. A passive system (with a Wye) works just fine if you don't need control over which bag fills.

  4. #14
    Join Date
    Feb 2012
    Location
    St. Albert, Alberta, Canada
    Posts
    170

    Default How did you plumb your IBS???

    Quote Originally Posted by jasonwm View Post
    Looks good! If you can, try to tilt that pump mounted to the panel so the pump head (where the hoses attach) is a little lower. That will help extend the life of the pump..
    Thanks!
    What could happen to the pumps? This is how the factory mounts them....



    Sent from my iPhone using Tapatalk
    2010 MOOMBA LSV
    340 CAT
    ACME 1235
    3100#'s




  5. #15
    Join Date
    Feb 2010
    Location
    Canton, Ga / Lake Lanier
    Posts
    1,600

    Default How did you plumb your IBS???

    Quote Originally Posted by lsvboombox View Post
    I ran the mastercraft y valve like you are planning. Main lin e in one line to the floor sac then i bought a y splitter(not a t) and ran one line to each leg....
    That's EXACTLY what I'm going to do.

    ImageUploadedByTapatalk1361064049.718597.jpg
    Distribution Manifold

    ImageUploadedByTapatalk1361064151.566000.jpg
    This is what it will look like when I'm done. Going to have 3 just like this in the regular side locker...





    Sent from my iPhone using Tapatalk
    SOLD! 2011 Mobius LSV 325HP EFI
    Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537

    Board: '12 LF Harley (Monster) 139
    Her Board: '11 Ronix Krush 128
    Kids Board: '13 Ronix Vision 120
    Skate: LF Faction 44
    Surf: LF Custom Quad & XXX


    Tow Rig:
    2011 Toyota Tundra CrewMax TRD Magnetic Grey
    3/1 Truxx Lift, and some other stuff...

  6. #16

    Default

    Quote Originally Posted by KRAK View Post
    Thanks!
    What could happen to the pumps? This is how the factory mounts them....
    Mounting the pump horizontally like that can potentially lead to failure of the bearings and or brushes. It's unlikely, and typically only happens when the pump head is higher than the motor, but it's cheap insurance to prevent having to replace a $200 pump, because it's usually after the warranty is over that it fails.


    Quote Originally Posted by E4NASH View Post
    That's EXACTLY what I'm going to do.

    ImageUploadedByTapatalk1361064049.718597.jpg
    Distribution Manifold

    ImageUploadedByTapatalk1361064151.566000.jpg
    This is what it will look like when I'm done. Going to have 3 just like this in the regular side locker...
    Sounds like a good plan, post some pictures when you're done.

  7. #17
    Join Date
    Nov 2003
    Location
    Land O Lakes, Florida
    Posts
    6,377

    Default

    Jason, in the photo above with the 3 pumps, which one is mounted correctly ?
    Hey, Its Moomba time

    Its all about the dash - enjoy the dash, as that is your time between the dates
    13 Mobius LSV-sold
    08 Mobius LSV-sold
    03 Mobius LSV-sold
    life is about finding the balance between being a responsible adult and staying young at heart

  8. #18

    Default

    Well, technically none of them are mounted wrong, since the pump head (where the hose connects) isn't above the motor. But we would prefer it if pumps were installed with the pump head below level with the motor. Based on that, the bottom pump is mounted correctly.

    Watch our product video on the Jabsco Ballast Puppy Pump for more information, I talk about installation at 2:00 in.

  9. #19
    Join Date
    Nov 2003
    Location
    Land O Lakes, Florida
    Posts
    6,377

    Default

    Quote Originally Posted by jasonwm View Post
    . Based on that, the bottom pump is mounted correctly.

    .

    Good news as that is how I remounted all mine, plus if one goes bad Ive got a spare in the box

    still going to watch the video tho
    Hey, Its Moomba time

    Its all about the dash - enjoy the dash, as that is your time between the dates
    13 Mobius LSV-sold
    08 Mobius LSV-sold
    03 Mobius LSV-sold
    life is about finding the balance between being a responsible adult and staying young at heart

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •