Results 1 to 10 of 28
Thread: prop shaft?
-
08-02-2012, 11:51 AM #1
prop shaft?
sooo i went outside to see if i could get my prop off and i was wondering if my prop shaft was bent...i think it is.. what do yall think haha..anyone know how much one runs and where online to get one...im not paying someone 100$ hr to replace it when i can..also im guessing ill need the support piece thats by the prop
013.jpg014.jpgLast edited by motosno963; 08-02-2012 at 11:59 AM.
2004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Exile XM7's
Exile Harpoon
Exile ZLD
Polk 10in sub (2)
Polk P330 amp (subs)
-
08-02-2012, 11:59 AM #2
Everybody on the board has said really good things abot these guys... http://elberts.com/
I think a new shaft is around 400.00 depending on what size etc...
Its possible that your existing shaft and strut could be straightened by a machine shop as well...
-
08-02-2012, 12:01 PM #3
i was thinking that but it almost looks like its off by an inch and i can see small per portions but that looks like a lot haha
2004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Exile XM7's
Exile Harpoon
Exile ZLD
Polk 10in sub (2)
Polk P330 amp (subs)
-
08-02-2012, 12:09 PM #4
Most often insurance will cover bottom hits. You'd be surprised how spendy it can be when you start talking about replacing the shaft, strut, shaft seal, and other hardware. Whether you're paying a shop to do it at $100/hr or not. Paying the deductible and biting the bullet can be a better option sometimes.
Might wanna check into it before you dive in.So when is this "old enough to know better" supposed to kick in?
2001 MobiusV - Slightly Modified...
-
08-02-2012, 12:14 PM #5
i dont have insurance on my boat..i know dumb.. but with how much i get paid at work i dont know if i could afford it right now..i only get paid like 11$ an hour
2004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Exile XM7's
Exile Harpoon
Exile ZLD
Polk 10in sub (2)
Polk P330 amp (subs)
-
08-02-2012, 12:25 PM #609 21v LAUNCH
99 Outback LS. Sold
run your engine after you change your oil
68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
Doug
-
08-02-2012, 12:41 PM #7Senior Member
- Join Date
- Jun 2008
- Location
- Eugene OR
- Posts
- 1,786
Do you have an issue with your boat just wanting to go right when you get up too speed? It also looks like what you hit took some off the prop.
2008 Outback V - Sold but never forgotten.
“Do not wait; the time will never be “just right.” Start where you stand, and work with whatever tools you may have at your command, and better tools will be found as you go along." -Napoleon Hill
-
08-02-2012, 12:44 PM #8
i used my phone..but thats how it looks with your eye too...my prop had small nic's missing to begin with..that log finished her off with that big dent in the side, im about to order a new prop...it vibrates when you first take off but not that bad when your wakeboarding..can barley feel it..the day i hit the prop i was pulling someone when i hit it..and we did 2 more runs before we took her in..and i dont think i have any issues with the boat turning( if i can remember)
Last edited by motosno963; 08-02-2012 at 12:46 PM.
2004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Exile XM7's
Exile Harpoon
Exile ZLD
Polk 10in sub (2)
Polk P330 amp (subs)
-
08-02-2012, 12:47 PM #9
i sent elberts an email..anyone else know where i could get a shaft?
2004 Outback Blue/white w/5.7 indmar 350, Direct Drive
Rockford fasgate cabins
Rockford fasgate 500w amp (cabin) and a kenwood HU (kmr700u)
Exile XM7's
Exile Harpoon
Exile ZLD
Polk 10in sub (2)
Polk P330 amp (subs)
-
08-02-2012, 01:30 PM #10
No place better than elberts. They'll get you the right one and a great price. My only issue was the collar on the end of the shaft was a little different so I had to get bolts of a different size (length and thread length) to attach to the transmission coupler. Looks like you will also need a 15 degree strut-- you can get this at skidim.
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!