Page 6 of 7 FirstFirst ... 4567 LastLast
Results 51 to 60 of 64
  1. #51
    Join Date
    Feb 2011
    Location
    Euless, TX
    Posts
    132

    Default

    What were you guys using to shim the mount to the tower? I bolted mine on and when I put my boards on, had issues with the mount swiveling around.
    2009 LSV Liquid Force Edition
    - Gravity III - Upgraded 900lb rear locker
    - Z5 Rack
    - ACME 1847
    - Polk MM6501UM - Kicker IX500.4
    - Kicker CompVX 12" - Kicker IX1000.1
    - Pair Wetsounds Rev 10s - JL Audio HD750/1
    - RGB LEDs

  2. #52
    Join Date
    Jun 2012
    Location
    Lake Amistad, TX
    Posts
    636

    Default

    Quote Originally Posted by Clamcakes View Post
    What were you guys using to shim the mount to the tower? I bolted mine on and when I put my boards on, had issues with the mount swiveling around.
    Any little piece of rubber, cut in small strips, lay it inside the bracket, then crank down on it till she's good and tight!
    http://www.homedepot.com/p/DBHL-1-1-...0#.UYfEnMpu7nc
    not this particular one, but just so you get an idea... any rubber coupling will do then you cut it what ever size you need
    2004 Outback Blue on White *Sold
    2008 LSV Blue on White
    EXILED with 6 SX65-M in cabin & 2 XM9s rockin the tower
    2 Kicker ZX700.5 Amps powering the entire boat with 2 10" Subs under the dash
    Krypt KMA4200 EQ under driver's side dash to control all the madness
    Z5 Cargo Rack annnnnnnd She's NEKKKKED....

    I'm no expert, I just read up on the Moomba Forum...

  3. #53
    Join Date
    Aug 2011
    Posts
    2,522

    Default Re: Rotating Board Rack Suggestions for XLV

    I cut this down and wrapped it around...

    http://www.menards.com/main/mobile/f...585-c-6613.htm

    Sent from my Nexus 4 using Tapatalk 2
    http://www.instgram.com/jlyons30
    2002 Moomba Mobius LSV - Sold
    2006 Moomba Mobius LSV - Sold
    2017 Moomba Craz - Enzos, Lead

  4. #54
    Join Date
    Feb 2011
    Location
    Euless, TX
    Posts
    132

    Default

    thanks...going to make a run to home depot today. Parrot I like what you did with the AC tubing for the surfboard rack. Noticed when I put a wakeboard in there, issues with it sliding around and slapping on the bottom board.
    2009 LSV Liquid Force Edition
    - Gravity III - Upgraded 900lb rear locker
    - Z5 Rack
    - ACME 1847
    - Polk MM6501UM - Kicker IX500.4
    - Kicker CompVX 12" - Kicker IX1000.1
    - Pair Wetsounds Rev 10s - JL Audio HD750/1
    - RGB LEDs

  5. #55
    Join Date
    Aug 2011
    Posts
    2,522

    Default

    Wolfman or someone in this thread mentioned it, pool noodles...

    Not sure what type of wake boards or surf boards monster design engineers use but the wake board rack is too small and the surf rack is too big.

    For $125? I can deal with it...
    http://www.instgram.com/jlyons30
    2002 Moomba Mobius LSV - Sold
    2006 Moomba Mobius LSV - Sold
    2017 Moomba Craz - Enzos, Lead

  6. #56
    Join Date
    Feb 2011
    Location
    Euless, TX
    Posts
    132

    Default

    where the heck did you find a black or gray pool noodle!?? Only pool noodles I see are neon colors, blue, green, pink etc. I'm thinking some AC insulation like this would work on those forks.
    http://www.homedepot.com/catalog/pro...17a041_300.jpg

    And yeah at $125 a pop I can deal with it too. I wish I could mount the racks higher like moombadaze, but the combination of my Z5 rack and Rev 10s wont allow it.
    2009 LSV Liquid Force Edition
    - Gravity III - Upgraded 900lb rear locker
    - Z5 Rack
    - ACME 1847
    - Polk MM6501UM - Kicker IX500.4
    - Kicker CompVX 12" - Kicker IX1000.1
    - Pair Wetsounds Rev 10s - JL Audio HD750/1
    - RGB LEDs

  7. #57
    Join Date
    Jun 2007
    Location
    Vancouver, WA
    Posts
    5,456

    Default

    Yep - that would work too. Look for the pipe insulation in about a 1/2" or so. I'd look for the uncut or unspliced so it will just slip over and you won't have to deal with any sticky mating edges.

    I found different thicknesses of pool noodles too. Wally World, Target, etc. Mine HAD to be yellow though
    So when is this "old enough to know better" supposed to kick in?

    2001 MobiusV - Slightly Modified...

  8. #58
    Join Date
    Aug 2011
    Posts
    2,522

    Default Re: Rotating Board Rack Suggestions for XLV

    Pipe insulation at Menard's..

    Sent from my Nexus 4 using Tapatalk 2
    http://www.instgram.com/jlyons30
    2002 Moomba Mobius LSV - Sold
    2006 Moomba Mobius LSV - Sold
    2017 Moomba Craz - Enzos, Lead

  9. #59
    Join Date
    Jul 2009
    Location
    Spokane, WA
    Posts
    503

    Default

    Are the stock forks a Monster product, or did those come from another company? The forks on these Monster racks look very similar, not to mention they are sized for the elongated oval bar that are on the stock towers (the somewhat newer stock towers that is).
    2015 Supra SC400
    08 LSV - Sold
    Go big, or go home.

  10. #60
    Join Date
    Aug 2011
    Posts
    2,522

    Default

    I noticed today the color is starting to fade on my racks... They still work great and still a great deal for the $$$...
    http://www.instgram.com/jlyons30
    2002 Moomba Mobius LSV - Sold
    2006 Moomba Mobius LSV - Sold
    2017 Moomba Craz - Enzos, Lead

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •