Results 1 to 10 of 12
Thread: Make hole in hull bigger
04-30-2012, 10:58 PM #1
Make hole in hull bigger
Any pointers on this before I plug in the drill? I don't want to chip or crack anything.
I need to bore out the hole the speaker wires are in. I need it big enough for some sort of rubber sleeve for the wires.
Last edited by rsinger; 04-30-2012 at 11:00 PM.past---------------2003 Outback SOLD
present------------2006 Supra Launch 21V
possible future-----2013 Mojo
05-01-2012, 01:53 AM #2
How much bigger do you need/want to go? You may be able to get away with just a shrink wrap type tubing cover over the wires instead of a loom or bulky sleeve and then not have to open it up that much at all.
Normally you tape over it really good and if using a hole saw, some run it backwards to cut through the gelcoat, then flip the switch and finish off the hole. But since you've already got the hole I'm wondering if you could get away with using a step drill bit. Just not sure how gentle that would be on the gelcoat, even with tape on it...The years have been kind, it's the weekends that have done the damage.
2001 MobiusV - Slightly Modified...
05-01-2012, 08:24 AM #3
Perhaps one of these would work?
If not then that looks like it is about a 3/8 hole already. But to be sure what size is the existing hole? You can pickup many size drill bits at Lowes or Home Depot. So if the existing hole si say 3/8 and you want to nudge it up a touch buy a 1/2 bit and run it in reverse to enlarge the existing hole. I'd then hit it gently with a step (conical) bit in reverse to taper the gelcoat a bit.
Last edited by KSmith; 05-01-2012 at 08:29 AM.Kraig - 2010 Outback V
05-01-2012, 09:04 AM #4
looks like theres enough room to squeeze some wire loom in that. I'd run loom and leave it if it was mine.
but to the original question, I'd probably use a dremel very slowly with tape across the whole area and a green metal stone bit on it.'06 Supra Launch 20SSV-gone but never forgotten
05-01-2012, 09:42 AM #5
Indeed if you just wanted the wires cleaned up some I like this braided sleeving and secure the ends with heat shrink tubing.
http://www.parts-express.com/pe/show...number=082-360Kraig - 2010 Outback V
05-01-2012, 05:38 PM #6
My advise is if you only need it slightly bigger use a file, or get the small bits with the sandpaper on them. The same as you would see on a Drimmel. If you need it larger then you can use a larger drill bit, run it in reverse. I would not run it forward at all with a pre drilled hole that size, it will grab and gripe and try to chunk out the gell.
Last edited by mmandley; 05-01-2012 at 05:47 PM.Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
08-03-2012, 01:28 AM #7
Not that you need to go with a hole saw but if you ever do and you have a pre existing hole use a piece of 3/4" plywood with the new hole drilled in it. Simply hold the plywood over the old hole and drill the new one. I was able to drill all five of my courtesy lights larger with no help since I could rest the plywood on my floor. To drill my five vent holes bigger I held the plywood and had a friend drill. All holes need to be filed after drilling or cracks will appear in your gel coat.-Jake
08-03-2012, 10:46 AM #8Senior Member
- Join Date
- Aug 2008
- Cottage Grove, MN
stick an appropriate sized cork in the hole for the hole saw center bit to bite on. I did this when inlarging my drain ports to 1". Worked like a charm.2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
08-03-2012, 11:12 AM #9
I posted this hint given to me by 11 Outback V.
Get a hole saw kit that has the spindle & interchangeable hole sizes. Stack the current hole size inside the desired hole size and the smaller bit will act as a guide/hold it in place.Drew
2016 Supra SA 450
2015 Supra SG 450
2012 Moomba Mojo
2008 Moomba OBV
08-03-2012, 12:25 PM #10
Easiest and safest method is to use a round file. It'll open it up in less than a minute and not risk destroying the gel coat. Put the power tools down for this job. When I put new thru hulls in I had to go a little lager than the 1" hole saw I used to make the initial hole. I used a round file and I swear it only took a few swipes to make a significant different to the size f the hole..2017 Moomba Craz