Results 41 to 50 of 65
-
06-04-2012, 10:31 AM #41Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 780
anyone have any video from behind the boat with the new surf platform to see how or if the water comes in contact with it?
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
-
06-04-2012, 10:36 AM #42
I've put up a few from my Mojo. I think it works great as it eliminates that "rooster tail" that the corner & lip create with with standard one. IMO, it creates a cleaner face on the wave.
However, it didn't improve my already mad skillz . . . .
-
06-04-2012, 01:20 PM #43
looked at a new lsv that had the new surf platform and can see how it will help with the surf wave spray that I get when surfing with my boat.
Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
06-06-2012, 08:10 AM #44
I just put one on my LSV 07. It sure takes a lot of pressure off the platform when surfing because the platform never touches the water. That was my main reason for the change. I do have to run 1/2 to 3/4 plate now, where before I ran 0 to 1/2 depending on the amount of ballast to keep the wake clean. I have 1100 rear & 400 center, and use a spare 750 on the seats if I don't have more than 3 or 4 persons.
07 LSV
-
06-06-2012, 08:27 AM #45Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 780
Why do you have to run 1/2 to 3/4 wake plate with the new platform? (I'm assuming you mean down, so 3/4 down would be almost parallel with the hull)?
Did you just order the platform through your dealer? How long did it take to get?
Also, did you reuse your existing brackets off the old platform, and how did you secure the new platform on? Sorry for the 20 questions....2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
-
06-06-2012, 04:12 PM #46
Need the plate now because the platform does not drag in the water like the old one did. My old one was actualy acting like the plate to some degree. Atlanta Marine did the install, using existing brackets. They drilled and tapped 4 bolts into the brackets to take the play out. It took 3 weeks for Moomba to ship it. I did call Skiers Choice to make sure it would work before I had them order it.
07 LSV
-
06-12-2012, 01:38 PM #47Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 780
I just ordered the surf platform from the new local dealer. Should have in about 3 weeks. Hope it's worth it.
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
-
06-12-2012, 02:43 PM #48
Please post some video of it on the LSV. Love to see what it does.
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
06-12-2012, 03:32 PM #49SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
06-12-2012, 04:25 PM #50Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 780
Jeffro, did you order yours with the SS rubrail? I ordered mine without it, since my current platform doesn't have one I didn't figure I'd miss it. And it seems like the screw holes for the rubrail would be a likely suspect for potential water intrusion into the platform.
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand