Results 1 to 10 of 17

Thread: Getting there

Hybrid View

  1. #1
    Join Date
    Jul 2011
    Location
    Rapid City, SD
    Posts
    89

    Default Getting there

    Worked on getting the wake dialed in for surfing. Definitely still got some work to do to clean up that mush on the wave. Didn't get any video of it but at one point the goofy side was crazy sick.

    I need to work on my ballast setup because for some reason when I fill up my one of my bags through the GIII they all fill up. I may dig into it today and check my "sprinkler system" and valves. So then they all fill up and then I have to drain the other side from surf. Takes way too long. So I got tired of filling ballasts and had kids getting restless in the boat, so it was time to surf. I think I was only 3/4 full surf vlocker and 3/4 full basement. Definitely need more list. Might get a Tsunami and a 400#er to put on surf side corner seat this week for labor day weekend.

    Anyways finally yesterday got the feeling of push and how to work with it. Then at the end of both videos I was able to let go of the rope for a bit


    2013 Tige RZR w/ConvexVX, WetSounds Rev10s, 6x650s, Syn4 and Syn6 amps.
    Surf Quiver 4x Brigade Wakesurfing Surf Boards- Aviator, Zulu, .352 Special, Bomber
    Victoria Skim 2xGremlins, 2x Agents, 1 Factor, 1 Pixie Bri Chmel Pro Model

  2. #2
    Join Date
    Jan 2008
    Location
    Tallahassee, FL
    Posts
    14,071

    Default

    You are definitely getting there and looking comfortable on the board. The wave is still pretty washed out. Some folks have used plastic garbage cans or bins as a cheap way to add ballast in order to figure out what they need. If you could get another 200 lbs. or so on the surf side I think that wave would clean up. Ideally you get a 750 bag for that rear corner though. Good progress so far though. I think you should shorten that rope by about 6 feet so you aren't fighting it so much.
    My Mom said I'm not allowed to get wet!
    2008 LSV (sold)
    2000 Outback LS (sold)
    LLTR!!!!!!!!



  3. #3
    Join Date
    Jul 2011
    Location
    Rapid City, SD
    Posts
    89

    Default

    Thanks Kane,

    I have a 750#er in both v-lockers. But like I am working on a thread in the Service and Repair area, my ballast system isn't working optimal, and with the kids getting antsy I thought it best to get in the water before I had a mutiny on my hands. My surf side 750 wasn't completely full. I am contemplating on purchasing a 400#er and a tsunami to put on the seat. The other thing I am thinking of is getting a bag to go under the seats on surf side and tie that into that GIII system.

    My rope has two sections to it. I took one off and it was a lot shorter than the other section so maybe I just swap sections and that should be the right length. Wife is loving to drive though. She likes driving for wakesurfing way better than wakeboarding. Plus I am right there to talk to her and walk her through any changes.
    2013 Tige RZR w/ConvexVX, WetSounds Rev10s, 6x650s, Syn4 and Syn6 amps.
    Surf Quiver 4x Brigade Wakesurfing Surf Boards- Aviator, Zulu, .352 Special, Bomber
    Victoria Skim 2xGremlins, 2x Agents, 1 Factor, 1 Pixie Bri Chmel Pro Model

  4. #4
    Join Date
    Jun 2007
    Location
    Vancouver, WA
    Posts
    5,457

    Default

    If you do an extra bag on the surf side with a handheld to experiment with I'd suggest doing it on the floor, then have the kids/passengers sit on the same side and they can just rest their feet on it. The boat should still lean over enough with that added weight and then you're not giving up and seating or access to the cooler!
    So when is this "old enough to know better" supposed to kick in?

    2001 MobiusV - Slightly Modified...

  5. #5
    Join Date
    Jul 2011
    Location
    Rapid City, SD
    Posts
    89

    Default

    Solid tip, thanks man. Off to the classifieds
    2013 Tige RZR w/ConvexVX, WetSounds Rev10s, 6x650s, Syn4 and Syn6 amps.
    Surf Quiver 4x Brigade Wakesurfing Surf Boards- Aviator, Zulu, .352 Special, Bomber
    Victoria Skim 2xGremlins, 2x Agents, 1 Factor, 1 Pixie Bri Chmel Pro Model

  6. #6
    Join Date
    May 2009
    Location
    North End Lake Lanier GA
    Posts
    8,155

    Default

    What speed are you going bro? Even with 750s not filled all the way as long as people stay on the surf side you can dial that in pretty easy. The regular side of the surf is much easier and forgiving. You might try a little faster speed and play with the wake plate. I try to always dial the wave in before people get in because once there in the wave its hard to see it clearly.

    You are looking good though and i can see the wave grabing and pushing you at times when you hit the sweet spot.

    Another thing to try when comming up on the surf wave is heel hard on the bard to cut wide when you first come up and get away from the wash then you wont be fighting to climb over that wave.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    [COLOR="#696969"]

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •