Results 1 to 10 of 45
-
08-24-2011, 06:56 PM #1
Bracing your V Drive locker for 1100 Fat Sacs
I received a couple emails on how did i brace my V Drive locker for my 1100 fat sacs.
Parts needed are all from Home Depot
4 3/4 x 48inch x 1/8th long aluminum angle bars. http://www.homedepot.com/h_d1/N-5yc1...atalogId=10053
6 1 inch Lag Stainless Steel Lag bolts
8 Stainless Steel bolts
8 Stainless Steel Machine screws
8 Stainless Steel washers
8 Stainless Steel lock washers
All the above can be substuted for what ever size you want. I persoanly used 24x10 i think it was.
I used 2 48 inch peaces as the bottom rail and used 3 lag bolts to attach that to the floor of the boat.
I then used the 2 other 48inch peases for my upward bracing. Front is apx 22inch high and the rear is apx 21 inch high.
I then bolts the upper braces to the lower angle bracket and then again to the upper cross member in the boat.
Make sure you watch for the locking tabs on the plastic doors. As you can see in my pic i mis measured by 1/2 inch and need to fix that now lol.
Also you will notice the engine actualy doesnt sit centered in the engine bay so pay attention to this when you place your upward braces.
This all cost me about 35 bucks. and 2 hours or 4 beers of time.
Passenger side bracket. Drivers looks the same.
1100 Empty
1100 Full on goofy side. You can see where my brace is blocking my panel hinge. That will be fixed ASAP.
I also need to repostion the 1100 bags slightly to allow them to sit a bit more upright.
I will post some video of the surf wave after this next weekend as we are still dialing it back in. I can say this with the 1050 nose ballast i run made a huge improvment wave is now even larger and the pocket is insainely long.Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]
-
08-24-2011, 07:03 PM #2
Nice work Mike! Looks great and cheap to boot!
Al
2006 Mobius LSV
-
08-24-2011, 07:22 PM #3Senior Member
- Join Date
- Jun 2008
- Location
- Eugene OR
- Posts
- 1,786
Mike Nice work. looks like it would cost more then just 4 beers to make.
2008 Outback V - Sold but never forgotten.
“Do not wait; the time will never be “just right.” Start where you stand, and work with whatever tools you may have at your command, and better tools will be found as you go along." -Napoleon Hill
-
08-24-2011, 08:30 PM #4Senior Member
- Join Date
- Aug 2008
- Location
- Cottage Grove, MN
- Posts
- 780
Awesome! Thanks for posting this. What size lag screws did you use to go into the floor? You list 1", but what diameter?
2006 Outback V - Gone
2008 LSV - Gone
2013 other brand
-
08-24-2011, 08:38 PM #5Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]
-
08-24-2011, 09:25 PM #6
Hey Mike. Thanks for the "How To". I had decided not to do it since my exhaust was so close to the v-drive door and have never had it push past the brace. However since you make it look so easy I think I will be running to Home Depot later.
------Sold-------
2008 MOBIUS LSV - Acme 1847, GIII w/1100lbs Vdrive, IBS, PPSG, Wake plate, Z-5, Kenwood 700U, Kenwood Kca-RC107MR , Exile SXT65, Kicker 700.5, Kicker 350.4, Polk MM651, JL 13.5 Thin-Line Sub.
-
08-24-2011, 09:26 PM #7Member
- Join Date
- Jul 2011
- Location
- Rapid City, SD
- Posts
- 89
Well done. Is this something that all of us should consider with bigger bags in the vdrive lockers? I have a 2x3 aluminum brace at a diagonal from high bow side to low transom side. Is that enough?
2013 Tige RZR w/ConvexVX, WetSounds Rev10s, 6x650s, Syn4 and Syn6 amps.
Surf Quiver 4x Brigade Wakesurfing Surf Boards- Aviator, Zulu, .352 Special, Bomber
Victoria Skim 2xGremlins, 2x Agents, 1 Factor, 1 Pixie Bri Chmel Pro Model
-
08-25-2011, 07:46 AM #8
-
08-25-2011, 03:39 PM #9
thats what i was wondering to.. that is a huge brace and i couldn't see how a bag could push past that? So i'm assuming that when they changed the hull design in 06 they changed that as well as my 05 has that angle bracket.
Geoff2014 Mondo with da flow!!! Exile towers, stock everything else.... for now!
-
08-25-2011, 03:42 PM #10
Nice job documenting this for everyone, Mike! You're all set for the big shindig now, right?
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!