Results 1 to 10 of 26
Hybrid View
-
08-23-2011, 07:08 PM #1Junior Member
- Join Date
- Jul 2009
- Posts
- 25
Putting T Handle in LSV. How do I remove the floor?
Just bought an 08 LSV and found out no T Handle. I test drove a 2010 with a center plug and didn't think about looking for one on the 08. So im going to add one to help it drain. The only hold up is the floor. How does the two metal plates come out? I have looked at most of the mods and cant find any screw.
Any help would be greatly appreciated and photos are a huge plus.
-
08-23-2011, 07:22 PM #2
I'm assuming your 08 is the same as my 06. There are four screws holding each panel down. They are very close to the corners of each panel with the exception of the corner near the driver's seat. On miine, that screw is about 6" from the corner, along the starboard side of the panel. The phillips screw heads are hidden in the carpet so you have to look for them but they are there.
Let us know how you do this mod. I am sure there are many of us that would be curious to see it.
AlAl
2006 Mobius LSV
-
08-23-2011, 07:25 PM #3
How do you plan to access the t handle ?
fyi, my 08-the forward floor panel only had 3 screws holding it down, there was none in the drivers corner.Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
08-23-2011, 08:07 PM #4
-
08-23-2011, 08:12 PM #5Junior Member
- Join Date
- Jul 2009
- Posts
- 25
thanks for the help. i plan on cutting out the center of the rear panel to make a door with a hinge over the hole in the gas tank. The 2010 has the same gas tank so i know i have room just need to lay it out and cut the hole in the floor and a 3/4 hole in the hull after taking the gas tank out.
I found this 2 seconds after writing the post. not what im doing but helpful none the less
http://www.wakeworld.com/forum/showthread.php?t=787634
pic of the 2010 with the access door
http://www.carolinainboard.com/newbo...10-moomba-lsv/Last edited by weston579; 08-23-2011 at 08:21 PM.
-
08-23-2011, 08:39 PM #6
I'd be interested in seeing how this works for the two of you guys. I always seem to have water stuck in the hull of the boat. The plug on the back of the boat to me seems useless.
2006 Mobius LSV
-
08-23-2011, 09:22 PM #7
-
08-24-2011, 07:20 PM #8
Here is a pic underneath
Sent from my DROIDX using Tapatalk
-
08-26-2011, 09:31 PM #9
Does the newer boats have a different fuel tank in them then previous years? Didn't know if this was something I could do to my 2006 or not. I was thinking the hole in the center of my tank wasn't as big as what is being shown in the pictures above. Another thing is does anyone know if there is away for someone to move the fuel pump to in tank like the pictures above show so that wouldn't have to deal with vapor lock. I konw the pump getting hot can't be good on the pump. Or atleast I know on cars it isn't.
2006 Mobius LSV
-
08-26-2011, 09:55 PM #10
Yeah it looks like the newer boats with the t-handle installed have a different tank setup. Here is a picture of the gas tank from Newty's 2008 LSV that he posted on wakeworld showing his DIY carpet replacement. My 2008 LSV gas tank is the same. I am guessing the 2006 would be similar to the '08. Easy enough to pull up your floor panels and check. There is a hole towards the front that appears to be big enough put a drain with a "T" handle in. I am going to be working on my boat tomorrow so I will try to take the measurements and see if the hull has a flat spot in the bottom of that hole.
The thread from Newty - http://www.wakeworld.com/forum/showthread.php?t=787634Last edited by 08LSV; 08-26-2011 at 10:03 PM.
------Sold-------
2008 MOBIUS LSV - Acme 1847, GIII w/1100lbs Vdrive, IBS, PPSG, Wake plate, Z-5, Kenwood 700U, Kenwood Kca-RC107MR , Exile SXT65, Kicker 700.5, Kicker 350.4, Polk MM651, JL 13.5 Thin-Line Sub.