Results 31 to 40 of 81
Thread: Prop Test Results Part 2
-
09-07-2011, 09:27 PM #31
Matt75 got the new OJ 5 blade and was nice enough to let me try out his acme 537 that came on his axis. My boat came with OJ wakeboard prop, 14.25x14, and his did not pull nearly as good as mine which is to be expected but it was butter smooth. My "ogre" was gone too! I have the stock OJ back on now but an 1847 will be purchased by next spring!
David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
09-08-2011, 03:17 AM #32
------Sold-------
2008 MOBIUS LSV - Acme 1847, GIII w/1100lbs Vdrive, IBS, PPSG, Wake plate, Z-5, Kenwood 700U, Kenwood Kca-RC107MR , Exile SXT65, Kicker 700.5, Kicker 350.4, Polk MM651, JL 13.5 Thin-Line Sub.
-
05-25-2012, 09:27 PM #33
My new 1847 with a prop puller should be delivered tomorrow so my question is: do I have to torque the prop or just tighten it tight?
Mobius LSV 2011
GIII, V2 Tower, Indmar 325,
-
05-26-2012, 08:59 AM #34
Take a sharpie and trace a line on the shaft at the front edge of the prop. When you put the new one on you can tighten it until it reaches the line. Should be in the right spot.
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
05-26-2012, 09:58 AM #35
-
05-26-2012, 11:21 AM #36
Thanks for the answer, I will try to find the tool to torque it.....I didn t get the prop today.....monday I hope
Mobius LSV 2011
GIII, V2 Tower, Indmar 325,
-
05-26-2012, 04:53 PM #37
Here's what my 1847 came with:
So when is this "old enough to know better" supposed to kick in?
2001 MobiusV - Slightly Modified...
-
05-28-2012, 06:22 PM #38
I received my new acme 1847. I notice that on one side ( the side you can see in the rear of the boat) there are perfect grooves in the metal, and on the other side it is like all the grooves has been sanded.....is it normal...are the two sides should be the same?
Mobius LSV 2011
GIII, V2 Tower, Indmar 325,
-
05-28-2012, 08:06 PM #39David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
05-28-2012, 08:24 PM #40
thanks for the answer.........so now I have to install it
Mobius LSV 2011
GIII, V2 Tower, Indmar 325,