Results 1 to 10 of 23
Thread: Ballast Timings and comparisons
03-10-2010, 06:38 PM #1
Ballast Timings and comparisons
Thanks to Moombadaze for helping me out with a little flow test timing compilation. I was curious as to how all of our modifications stack up with our different methods of upgrading the stock ballast or building new systems. Surprisingly the results are not that drastic between the different methods. Some of the results were a lot lower than what I would have expected. You can use the chart to divide your total weight by 8.35 (Weight of a gallon of water) and then divide that by the GPM of each setup. If you are going to use a three Tsunami pumps to fill 3 450 pound bags, your fill time would be around 7.19 minutes, since the pumps can pump at 7.5 gpm to each bag the fill time will match the chart. These timings get a little more complex with the multi valve setup. From the chart you can see my newest setup can do 11.54 gpm through 1 valve filling a 450 in 4.67 minutes three minutes faster than a single Tsunami, but filling 3 450s through three valves will take 9.33 minutes which is 2 minutes slower than three single Tsunamis. With all that said, either method is better than the stock 20 plus minutes and the end result is less than two minutes of fill time.
If you can do a test that is not listed above (Hint hint Ed with those Jabscos), please email me the test you performed, boat model and timings. These tests must be done through the full setup like Moombadaze has done not from just a pump dumping water. The GPM of a Tsunami 800 is 13.33 GPM at the head, but is 7.5 gpm through all of the hoses and fittings as in Stacy’s case. If you are already on the water, pull one of your bags fitting and time how long it takes to fill a 5 gallon bucket, you can use a 1 gallon bucket, but a 5 gallon one will give you a better average.
My tests were done very similar to his, 5 gallon bucket pumped dry and timed. Time was divided by 5 to get the Gallon Per Minute (GPM) and the chart filled in appropriately.
Also If I have made any mistakes with my Shade Tree calculations, please correct me where I have given invalid data. The data will be different for some models hose length and pump location are a HUGE factor. I still need to fill in a few boxes this weekend from the new valves with the old pump.
So if you ask me which setup should you go with, my answer would be "It depends". In some cases each method is faster.
Stock setups are highlighted in Yellow.
15 Mondo Surf Edition
02 LSV - Traded In
03-10-2010, 06:50 PM #2
Great idea! I'm working on my Tsunami 1200s w/ 1" lines install now and should have some data for you next week.Dan
08 LSV Mods
03-10-2010, 06:50 PM #3
Nice work putting this together, Gotta say thanks to you Jesse as I never would have done bench timing test if you had not done it first.Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
03-10-2010, 10:19 PM #4
Would like to see 3 800 pumps, 3 intake results with vented loop results; 3 800 pumps, 1 intake with vented loops. Also, are the stock sprinkler valves in the 08 GGIII system the 3/4" valves? Judging by the numbers looks like it would take well over 20 min to fill a center sac with two 750 rear sacs.
03-10-2010, 10:26 PM #5
Outstanding work. I hope to have some 09 numbers with an upgrade for ya in about 5 weeks....blah if the ice is gone09 21v LAUNCH
99 Outback LS. Sold
run your engine after you change your oil
68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
03-10-2010, 10:40 PM #6
Thats really helpfull. I have the 2000 pump and the 3/4" orbit valves. So just by upgrading to the Irritrol 700 valves at 3/4" I can cut my fill time in half. Thats awsome! Thats like a $50.00 or $60.00 upgrade!2005 Moomba XLV, Polk db651 cabin speakers, 12" Kicker Comp, Bullet 6.5" hollow points in Arial Double cans, fosgate amps.
03-10-2010, 11:15 PM #7
03-19-2010, 01:36 PM #8Junior Member
- Join Date
- Mar 2010
What pump is this system using at 2,000 GPH, make and model, is this a two pump in and out system for multiple bags? Is the pump self priming? Aslo What type of thru-hull should be installed size, and maybe a model and what location of boat?
03-19-2010, 03:02 PM #915 Mondo Surf Edition
02 LSV - Traded In
03-21-2010, 10:04 PM #10Junior Member
- Join Date
- Mar 2010
http://www.boatersland.com/att665533.html is that the correct thru-hull? Also found the pump I think : http://www.rivermarinesupply.com/xca...e_1600GPH.html
How is th epump connected if it is not self priming?