Results 1 to 10 of 31
Hybrid View
-
01-03-2011, 10:59 PM #1Member
- Join Date
- Feb 2010
- Posts
- 54
Question!!! cabin amp and speakers
Hi there guys,
I have 6 beautiful db651's ready to be put in and also a pioneer 760 2 channel amp. I have decided after talking to a few of you that i am going to be running the rear 4 speakers off the amp and the bow speakers off the hu. will this be a good install? How should i go about wiring the speakers?
Thanks!!
rjgaumer2006 Moomba Gravity XLV. Cabin speakers: db651 on 1200.4 JL Tower Speakers: 4 WetSounds Pro 60, GIII with 750's in the Stern and 1100 in Bow. Wakeplate.
-
01-03-2011, 11:00 PM #2Member
- Join Date
- Feb 2010
- Posts
- 54
oh and here are the specs on the amp:
https://www.store.pioneerelectronics...eries/GM-5400T2006 Moomba Gravity XLV. Cabin speakers: db651 on 1200.4 JL Tower Speakers: 4 WetSounds Pro 60, GIII with 750's in the Stern and 1100 in Bow. Wakeplate.
-
01-03-2011, 11:44 PM #3
Although a 4chnl would be optimal for running 6 in-boats, if it were I, using what I had, I would run 3 speakers per chnl wired series/parallel. This would be a 2.6 ohm per chnl load, and net each speaker about 60+ watts each.
That's less then the a pair per chnl will receive, but IMO, better then leaving a pair on the head-unit.
-
01-03-2011, 11:46 PM #4Member
- Join Date
- Feb 2010
- Posts
- 54
is that 60 rms to each? or max?
2006 Moomba Gravity XLV. Cabin speakers: db651 on 1200.4 JL Tower Speakers: 4 WetSounds Pro 60, GIII with 750's in the Stern and 1100 in Bow. Wakeplate.
-
01-04-2011, 12:04 AM #5
-
01-04-2011, 12:11 AM #6Member
- Join Date
- Feb 2010
- Posts
- 54
so that should be good for the db651's then. correct? i am a complete door knob when comes to wiring audio equipment. is there any way you could make a diagram in the paint program or any other program and post it?
thanks a ton!2006 Moomba Gravity XLV. Cabin speakers: db651 on 1200.4 JL Tower Speakers: 4 WetSounds Pro 60, GIII with 750's in the Stern and 1100 in Bow. Wakeplate.
-
01-04-2011, 01:29 AM #7
I would personally buy a 4 or 6 channel amp to power the 6 cabin speakers but if you have made up your mind, then this is how you would wire the speakers:
Run a speaker wire from the port side rear speaker #1 "+" terminal to the amp. Run another wire from the port side rear speaker #2 "+" terminal to the amp. At the amp, twist the two wires together and connect it to the left channel's "+" terminal. Repeat for the "-" terminals. Repeat for the starboard side, connecting the starboard side speakers to the right channel.
Wire your bow speakers to the head unit as normal.
Hope that helps.
AlAl
2006 Mobius LSV
-
01-04-2011, 01:31 AM #8Member
- Join Date
- Feb 2010
- Posts
- 54
perfect. thank you so much!!
2006 Moomba Gravity XLV. Cabin speakers: db651 on 1200.4 JL Tower Speakers: 4 WetSounds Pro 60, GIII with 750's in the Stern and 1100 in Bow. Wakeplate.
-
01-04-2011, 01:42 AM #9
If you go the above route, then wire the bows to the head-units front chnls and use the H/U's "Rear" RCA output for your amp. This will allow you to fade back to the cabins when you want to crank the volume. This will help minimize the clipping to the under-powered bow speakers.
-
01-04-2011, 01:44 AM #10Member
- Join Date
- Feb 2010
- Posts
- 54
ok thats great to know also. do you know the answer to the question above that?
2006 Moomba Gravity XLV. Cabin speakers: db651 on 1200.4 JL Tower Speakers: 4 WetSounds Pro 60, GIII with 750's in the Stern and 1100 in Bow. Wakeplate.