Results 361 to 370 of 433
-
09-22-2014, 04:45 PM #361Senior Member
- Join Date
- Oct 2013
- Location
- Ft. Collins, CO
- Posts
- 688
I just used a dremel with a spiral cut bit. Fiberglass is easy to cut.
2007 Mobius LSV
1989 Sanger Skier DX - sold
-
09-23-2014, 12:19 AM #362
Check amazon for the hole saw, a lot cheaper then Home Depot
2007 Moomba Outback V
-
09-23-2014, 09:22 AM #363Senior Member
- Join Date
- Jun 2007
- Posts
- 883
kind of weird, but i've had this 2006 LSV since 2008 and look what I noticed looking forward in the ski locker..
was this hole a concern before even we knew about it? how could the previous owner of noticed it and corrected it?
at least it looks like it was addressed in some way.2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
09-23-2014, 09:38 AM #364
that's void that created the buzz a few years ago in the manufacturing process on the older models. only fix is to cut a deck plate and suck out water as needed.
A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
09-23-2014, 10:10 AM #365Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
09-23-2014, 10:17 AM #366
Water trapped between hull and ski locker subfloor
It's hard to say because the photo is hard to get a clear grasp of, but that looks quite similar to how my 08 looks up there. I think that is the factory product...
Which we know doesn't work. I have to suck the water out after every trip, even if I dont take a wave over the bow.'08 Mobius LSV- SOLD!
2017 Mojo Pro
-
09-23-2014, 10:25 AM #367Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
09-24-2014, 10:05 AM #368David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
09-24-2014, 12:38 PM #369Senior Member
- Join Date
- Jun 2007
- Posts
- 883
-
09-24-2014, 02:18 PM #370
I just found a 4 - 1/2" hole saw on Amazon for $33.00
http://www.amazon.com/DEWALT-D180072...+5%22+hole+saw2007 Moomba Outback V