Results 61 to 70 of 113
-
06-28-2011, 06:35 PM #61David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
06-28-2011, 08:08 PM #62
Guys,
If the gap is uneven and it's closing to zero when the bolts are tightened, then that means the shaft is bending or the couplers are deforming. The specified torque on the bolts is only 30 ft-lbs and if you tighten the 4 little bolts to that spec, it's not going to be enough force to bend the shaft or the couplers and close the gap to zero. Make sense?
AlAl
2006 Mobius LSV
-
06-28-2011, 08:30 PM #63
-
06-28-2011, 09:11 PM #64
not sure. and mine is not torqued exactly to 30 ftlbs, i dont see how yall get a torque wrench on there. i had hell with two box wrench. i didnt really crank on it and the rachet i used was only 1 foot or so long and i dont think i put more than 30 lbs of force on it.
David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
06-28-2011, 09:35 PM #65
Well, I know mine are torqued to 30 and there is a gap all around between the couplers from about .003" to .007" if I remember correctly.
yeah, it's a little tricky but it can be done. You have to rotate the coupler to get the bolts in just the right place.Al
2006 Mobius LSV
-
06-29-2011, 09:55 AM #66
-
06-29-2011, 10:37 AM #6709 21v LAUNCH
99 Outback LS. Sold
run your engine after you change your oil
68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
Doug
-
06-29-2011, 03:08 PM #68
Sorry guys, I stand corrected. I rechecked the gaps after I tightened down the trunnions pins, not the coupler bolts, and at that time, I had gaps varying from about .003" to about .007". I didn't want to messs with it any further at that point and tightened up the coupler bolts. Sorry for the confusion.
Al
2006 Mobius LSV
-
06-30-2011, 01:06 PM #69
Check out this article on alignment. Lots of good stuff-- be sure to note the stuff about V-drives.
http://www.yachtsurvey.com/Alignment2.htmMy Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
06-30-2011, 06:37 PM #70
so basically aligning it on land the trailer is pointless and as long as it its close it is good to go lol. thats what i got from that article.
David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD