Search:

Type: Posts; User: VA LSV

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    282

    Best option is to use a vacuum fluid extractor...

    Best option is to use a vacuum fluid extractor and suck it out from the engine drain hose. Several have posted about their vacuum extractor hose getting stuck in the dip stick tube. My extractor...
  2. Check the large breaker/disconnect near the...

    Check the large breaker/disconnect near the battery, safety cutoff switch under the throttle and make sure you are in neutral. Several people have also had issues with loose connections on the...
  3. Replies
    11
    Views
    310

    Take an O-ring off, go to your local hardware...

    Take an O-ring off, go to your local hardware store and match it up. I had some leaking issues and was going to replace O-rings but a little silicone lube took care of it.
  4. Replies
    11
    Views
    310

    Try putting some Vaseline or silicone grease on...

    Try putting some Vaseline or silicone grease on the O-rings.
  5. Replies
    1
    Views
    143

    Try these guys https://www.greatlakesskipper.com

    Try these guys
    https://www.greatlakesskipper.com
  6. Replies
    6
    Views
    167

    I would get the boards and send them out myself. ...

    I would get the boards and send them out myself. Doubt the dealer would want to be involved with that. Looks to be just power switching with minimal board level components. Should be easy to...
  7. Replies
    6
    Views
    167

    Look for an electronics repair in your area. ...

    Look for an electronics repair in your area. Probably just some broken solder joints.
  8. The actuators are hydraulic and fluid is pumped...

    The actuators are hydraulic and fluid is pumped from a power unit which has a small tank with an integral pump. Is your boat an LS direct drive or an LSV v-drive? The tank is located in the front...
  9. Replies
    1
    Views
    149

    Teleflex CH2200 looks like a good fit but check...

    Teleflex CH2200 looks like a good fit but check with these guys.

    skidim.com
    803-345-0996
  10. Replies
    44
    Views
    7,753

    Confirm you have 12 VDC to the solenoid. Swap...

    Confirm you have 12 VDC to the solenoid.
    Swap solenoids with 1 of the valves that is working.
    If you installed a new Orbit valve complete with the solenoid, check the voltage rating on the new...
  11. Replies
    12
    Views
    687

    In Virginia the minimum age to operate a PWC is...

    In Virginia the minimum age to operate a PWC is 16 and requires you to complete a boater course to receive a boat operators license. People can be annoying whether on PWC's or boats when they are...
  12. Replies
    6
    Views
    419

    The factory Gravity 3 ballast system should have...

    The factory Gravity 3 ballast system should have 3 switches below the throttle to control fill/empty of each bag. Stock rear bags were 250# and the floor locker 400#. Check that the fill valves...
  13. I switched to Irritrol valves when 1 of my Orbits...

    I switched to Irritrol valves when 1 of my Orbits failed and it did reduce my fill times. I didn't want to go the reversible pump route since I usually putter to the end of my cove while filling...
  14. Check that the manual override isn't on. It's a...

    Check that the manual override isn't on. It's a little black lever on the valve. Quick cheap fix would be to pickup a 3/4 irrigation valve from any home improvement store and swap it out. Factory...
  15. Replies
    13
    Views
    408

    Check with these guys. https://www.skidim.com/

    Check with these guys.
    https://www.skidim.com/
  16. Replies
    25
    Views
    1,333

    Blower in my '05 is located on the port side. ...

    Blower in my '05 is located on the port side. Remove the divider panels to get access. Invest in a wave shaper or build your own "suck gate". You can find plenty of specs on line. Easy DIY...
  17. Replies
    1
    Views
    133

    Check with these guys. skidim.com

    Check with these guys.
    skidim.com
  18. Thread: Wakeboard Rack

    by VA LSV
    Replies
    17
    Views
    7,182

    https://www.fluidconcepts.net/Wakeboard-Rack-Moomb...

    https://www.fluidconcepts.net/Wakeboard-Rack-Moomba-p/pf1.2-oval-ano-m.htm
  19. Replies
    11
    Views
    655

    Check the draft specs on the Moomba model you are...

    Check the draft specs on the Moomba model you are considering. Border line for sure plus sand would shorten the raw water pump impeller life.
  20. Replies
    1
    Views
    99

    https://www.skidim.com/prodinfo.asp?number=WAL49

    https://www.skidim.com/prodinfo.asp?number=WAL49
  21. Replies
    3
    Views
    162

    Check here skidim.com

    Check here

    skidim.com
  22. Thread: Stuck Prop

    by VA LSV
    Replies
    8
    Views
    489

    The prop is a taper fit to the shaft and...

    The prop is a taper fit to the shaft and shouldn't be lose. Sounds like your key has deformed since it was taking all the force and you will have to drive it out with a punch.
  23. Thread: Battery specs?

    by VA LSV
    Replies
    5
    Views
    267

    1000 CCA is pretty standard for marine starting...

    1000 CCA is pretty standard for marine starting batteries. What is the relay located and what is wired to it.
  24. Replies
    2
    Views
    412

    I'd be interested in the key fob but don't have a...

    I'd be interested in the key fob but don't have a need for the other items.
  25. Also these guys. www.skidim.com/

    Also these guys. www.skidim.com/
Results 1 to 25 of 302
Page 1 of 13 1 2 3 4