Search:

Got 1 vent installed on rear left bag. In testing it didn't work correctly.

I installed it in the fitting closest to the bow on the boat. Check valve is facing the correct way. Moved the drain...

Exactly. To vent the bag automatically without having to burp it. I understand how to install the check valve, just not sure where to tie it into the drain line. The check is there to keep the drain...

Wish my temp gauge worked. Never moves. Think the guage is bad as I have grounded the sending unit wire and still no movement. New thermostat end of last year and impeller this year and haven't run...

I was planning on repurposing those bags up their in that spot, and plumbing them in (future project). I have a pitch over the side pump from wakemakers I plan to use for the time being.
I may have...

I think My post might have been misunderstood. I am going to tee in the vent to the bag drain on each specific bag. No connections bag to bag will be shared. Ie left rear bag vent to left rear bag...

No vents on the factory system. It forces water past drain pump. My center pops the hatch in my lsv. I am currently installing vents in my system. Wakemakers has everything you need, but you will...

I am in the process of installing vents and tying them to the drain lines on my 05 LSV. Do I have to run hose all the way to the thru hull or can I tee or y in at any point in the drain line?

I...

Any info on these new HLCDs from kicker? Can't find anything on there website.

Sent from my SM-N950U using Tapatalk

I have the kicker HLCDs and they scream. I also got a new set from Walmart over the winter and they were discounted down to 120.

For budget amps look at PPI phantom series. They are class D so...

I am committed at this point, as the intake is dangling. I'm not sure if I can get it resealed without getting it completely off.

Sent from my SM-N950U using Tapatalk

I can't get the 90 degree street tee off the intake scrupper. I have the scrupper loose and ready to drop out but can't until the thru hull nut comes off, and the street 90 is in the way. Its acts...

Walmart has the Kicker KMS67 HLCDs for $120! (This is the no Pod kit)

...

I lost the port rear end of season. Have a 800 on the way. Hit the wakemakers black Friday sale on a few things. The other two are Factory pumps. The center pump drains relatively quick however the...

I got a brass reducing tee, 3/4 on the T portion, and 1" on the main run. Have 2 1" ball valves to put on the T and ordered 2 Tsunami 1200s to feed the manifold, and jettisoning the sprinkler valves...

If its all 3/4 npt, the smallest tsunami 1200 inlet is 1" npt. Will you have to have an adapter for the pumps to make it work? Working on replacing the rule 2000 myself also. My factory manifold is...

I can answer... Phantom series. And they are phenomenal. Had them in my last boat. Excellent price/value

Sent from my SM-G930V using Tapatalk

They are not on the floor, they are suspended on a board!...

This is what it was before, like this when I got it. Garbage....

This is what it is now....

Home depot or Lowes has reinforced hose by the foot.

Sent from my SM-G930V using Tapatalk

Replaced plugs yesterday, 4 were black, and they were all about .055 gap except for one of the black ones. it was around .030. They looked to be the originals, but I am not sure. They were the...

Developed a cold start issue.

Wants to start cold and does but idles too low and dies. I can advance the throttle a tad, and she starts right up. No issues starting once warmed up, starts with a...

My understanding is that that year outback is the same gull as my 05 mobius lsv. This is what I have been able to get out of it so far. 750 left rear, half to two thirds full on the right 750, and...

Mostly down. Anything up and it washes out.

Sent from my SM-G930V using Tapatalk

First picture was before with 750 port and 260 center full without suck gate. 2 people in the boat. Washed out once I got in the water.

Second picture is 750 port full, 750 stb about half to 2/3,...