Search:

Type: Posts; User: OBV6

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. If I read your post correctly, when the screws...

    If I read your post correctly, when the screws are placed in the leg holes they dont line up with the threaded hole on the tower. The leg ends on mine rotate to line up with the tower. They may not...
  2. Thread: Tarp or No Tarp?

    by OBV6
    Replies
    8
    Views
    3,377

    I think if you took a survey on this, a majority...

    I think if you took a survey on this, a majority of us have tried the tarp in some form or another and ultimately found that there is really no substantial benefits to it other than piece of mind. I...
  3. Replies
    2
    Views
    2,256

    The actual trans cooler is located on the outlet...

    The actual trans cooler is located on the outlet end of the raw water pump on the right/driver side of the block. There is a brass drain plug on the bottom of it, but I personnaly pull the inlet hose...
  4. Replies
    21
    Views
    7,161

    Muffler

    Viking, from the looks of it there is a crack on the back side of the muffler and most likely on the radiused transition from the inlet end to the body (thinnest part). As easy as it appears to take...
  5. Replies
    10
    Views
    4,080

    V drive service

    For DOCDRS and anyone else that has to or wants to get inside of the Walter Vdrive for service it is a 4 bolt easy job. I had some weeping coming from my Walter V drive on my 06 OBV so I thought I...
  6. Thread: Upholstry Repairs

    by OBV6
    Replies
    3
    Views
    1,501

    Upholstery

    Schneider, the skins for an 06 OBV are $140.00 ea for the L/R sections and $180.00 for the engine cover from SC through my dealer. If you have an XLV/LSV they will most likely be higher. Labor will...
  7. Replies
    43
    Views
    12,296

    Dollies

    Spyder before you buy the Harbor Freight dollies make sure they will support the weight. I got some for my SA Boat mate and the dolly wheels literally rolled outward under the weight. They were rated...
  8. Replies
    3
    Views
    2,216

    Sun deck upholstery replacement

    In case anyone was wondering, the cost to replace the upholstery on the rear deck of an '06 OBV will run you about $500 and tax. L & R skins are $140.00 ea and the engine cover is $185.00. Be sure to...
  9. I agree with everyone in the previous posts. On...

    I agree with everyone in the previous posts. On the trailer I would rotate the wheels some to lube the bearings and reduce tire cupping and check the inflation. If you haven't changed the oil in the...
  10. Replies
    6
    Views
    2,717

    FS: 2006 Moomba Outback V

    2006 Moomba Outback V Wakeboard boat
    Indmar 5.7L 325 HP Assault motor
    325 hours
    Perfect Pass
    Gravity Games III ballast system w/ upgraded F.H. 400lb bags/ bag vents
    Adjustable wake plate...
  11. Thread: Inboard Service?

    by OBV6
    Replies
    5
    Views
    1,795

    Extreme Powersports in Greenville, IL is a...

    Extreme Powersports in Greenville, IL is a Supra/Moomba/Natique dealer. Bought my OBV from them, great to work with.

    Extreme Power Sports, Inc
    Phone: (888) 469-0434
    Fax: (618) 664-3371
    Toll...
  12. Replies
    1
    Views
    1,666

    2006 Moomba Outback V

    2006 Moomba Outback V Wakeboard boat
    Indmar 5.7L 325 HP Assault motor
    310 hours
    Perfect Pass
    Gravity Games III ballast system w/ upgraded F.H. 400lb bags/ bag vents
    Adj wake plate
    Rad-a-cage...
  13. Thread: Vapor lock

    by OBV6
    Replies
    8
    Views
    5,504

    Jim, I have an 06 OBV with the 325 motor that...

    Jim, I have an 06 OBV with the 325 motor that also had the same vapor lock issues. I am guessing that mine was from almost 5 years of E85 gas. Any way, I replaced the inline fuel filter with a new...
  14. Replies
    23
    Views
    20,727

    Was looking for a fuel/water seperator on mine...

    Was looking for a fuel/water seperator on mine when I replaced the fuel filter. I also called my dealer to verify that there was not some sort of stealth seperator that I wasn't seeing. The service...
  15. Replies
    23
    Views
    20,727

    NAPA part # 3299, it is a little shorter that the...

    NAPA part # 3299, it is a little shorter that the CarQuest filter that SC puts on. Replaced mine last week for the same reasons, also put in StarBrite-StarTron fuel treatment. Ran the fan when...
  16. Replies
    5
    Views
    1,390

    Upper most hose coming from the raw water pump...

    Upper most hose coming from the raw water pump (at the rear of the boat) goes right into the trans cooler sleeve just before it enters the block. Pull the hose off the bottom of the sleeve and inside...
  17. Replies
    5
    Views
    1,390

    Port side (left) is the intake for the engine,...

    Port side (left) is the intake for the engine, raw water pump and the right side is for the ballast. Make sure you clean out the trans cooler when you replace the impeller. It is the first and pretty...
  18. Thread: 13.5 x 17.5 prop.

    by OBV6
    Replies
    6
    Views
    2,397

    Not a bad wake board prop for my kids and I don't...

    Not a bad wake board prop for my kids and I don't have a problem getting up boarding either (195 lbs). On my 06 OBV (325 Assault) I can hit @ 40 top end empty and cruise at 29 mph @ 3100 rpm. It is...
  19. Thread: my 4th weekend

    by OBV6
    Replies
    3
    Views
    1,427

    My thoughts as well. Normally a moving strike...

    My thoughts as well. Normally a moving strike gets all four blades, ask my wife! If it is rough on the end it is most likely a rock/ramp etc..
  20. Replies
    9
    Views
    5,597

    Looks great, are you running north of the...

    Looks great, are you running north of the Conservation club or down by Trice landing when you put in. Saw your boat before you put the speakers on a few weeks back but haven't seen it since.
  21. Replies
    2
    Views
    2,403

    If for some reason you impeller vanes get...

    If for some reason you impeller vanes get shredded they will collect inside the trans cooler sleeve mesh. Trans cooler is located on the outlet side (upper hose) of the raw water pump and there is a...
  22. Replies
    8
    Views
    5,330

    I have been doing a lot of research IOT replace...

    I have been doing a lot of research IOT replace my Kenwood HU as well. According to everything that I have been reading here on the other threads and in the Crutchfield web site, so long as the HU is...
  23. Replies
    1
    Views
    2,333

    Back in the day some battery companies used to...

    Back in the day some battery companies used to make a removable carrying handle that was essentially the female ends of 2 battery cables connected by a rubber strap. I have also seen what appears to...
  24. Replies
    16
    Views
    3,308

    You have probably already tried this, but is it a...

    You have probably already tried this, but is it a reverse thread pattern. Last resort call SC and ask, most likely they have some sort of high dollar puller.
  25. Replies
    16
    Views
    3,308

    If the pump is no good it means you don't have to...

    If the pump is no good it means you don't have to worry about ruining it trying to take it off. Why not try heating the plate with either an acetylene torch or propane soldering torch. If you can get...
Results 1 to 25 of 43
Page 1 of 2 1 2