Search:

Type: Posts; User: bubba_tiger

Search: Search took 0.01 seconds.

  1. I hope that's not the case, but we'll see on day!...

    I hope that's not the case, but we'll see on day! Thanks.
  2. Retaining nut & coupling set screw question

    I have an '04 mobius and I am replacing my shaft seal. When removing the retaining nut from from shaft I noticed that it was not very tight. When reinstalling everything back, I tightened the nut to...
  3. How to identify correct Intake Manifold Gasket

    Can anyone help me locate the correct gasket that fits between the upper & lower intake manifolds? I have a small oil leak. The boat is a ’04 Mobius.

    Also, would that cause the engine to run rich...
  4. Replies
    3
    Views
    2,564

    Thanks for the advice!!!

    Thanks for the advice!!!
  5. Replies
    3
    Views
    2,564

    EFI - Rich fuel mixture

    I have a 2004 Mobius LSV, and this is the first season I have had it on the water. The Indmar engine is EFI (throttle body injection). I believe it is running rich because it seems to act flooded...
  6. Replies
    8
    Views
    3,809

    UPDATE: I had already taken the bolts out, and I...

    UPDATE: I had already taken the bolts out, and I just loosened the boot clamps and pulled everything away from the shaft log. The shaft still wants to remain in the upper right side of the shaft...
  7. Replies
    6
    Views
    2,466

    I will. I believe they will advise me to just...

    I will. I believe they will advise me to just upgrade, but we'll see. Thanks!
  8. Replies
    8
    Views
    3,809

    Yes I do have a v-drive and yes sir, moving front...

    Yes I do have a v-drive and yes sir, moving front of motor in 3 oclock direction will help the coupling alignment. But first I want to get the shaft in the in the center of the shaft log while...
  9. Replies
    8
    Views
    3,809

    Doc, fairly well was touching at 12 oclock & 3...

    Doc, fairly well was touching at 12 oclock & 3 oclock. I could get .0025 in at 6 oclock & .0003 at 9 oclock. Bolts have been removed, and I do not believe the shaft is bent because the spacing...
  10. Replies
    8
    Views
    3,809

    Thanks for the advise, and it makes sense. Found...

    Thanks for the advise, and it makes sense. Found out the strut is new (installed in Jun '17). The previous owner did not try and center the shaft to log when installing the strut. The coupling is...
  11. Replies
    8
    Views
    3,809

    Prop shaft to shaft log alignment

    Got under boat and noticed my prop shaft was way off center to shaft log:

    2646726468

    This is probably common knowledge, but do I need to disconnect the shaft seal (I've got PSS) from log before...
  12. Replies
    6
    Views
    2,466

    I emailed Beede Instruments and they advised me...

    I emailed Beede Instruments and they advised me that the gauge and module are both obsolete. Attached is most of the info they sent me (file was too big to attach everything).

    Problem I am having...
  13. Replies
    6
    Views
    2,466

    Wakeplate gauge issues

    My wakeplate on an '04 Mobius LSV is not working. Based on previous posts, I started tracing wires and most of them went to a black box (relay??). All the additional wires on the box has been cut. ...
  14. Replies
    11
    Views
    2,325

    Appreciate all the great feedback. Thanks!!!

    Appreciate all the great feedback. Thanks!!!
  15. Replies
    11
    Views
    2,325

    Boat lift redesign for an '04 Mobius

    I'm a new inboard owner. Really appreciate the wisdom (winterization) on this site. I just purchased an '04 Mobius LSV and I'm looking for some advice on redesigning the conventional boat lift so...
Results 1 to 15 of 15