Search:

Type: Posts; User: Engine Nut

Page 1 of 3 1 2 3

Search: Search took 0.07 seconds.

  1. Replies
    27
    Views
    1,156

    You really need to get with someone that has a...

    You really need to get with someone that has a scan tool. ROM limited to 2000 might just be an issue that is causing the ECM to limit the RPM to avoid damaging something.

    You have a throttle by...
  2. Replies
    2
    Views
    282

    The Indmar P/N for that dipstick is 903064. Any...

    The Indmar P/N for that dipstick is 903064. Any Indmar dealer can order one for you.
  3. Replies
    10
    Views
    621

    We use a wire reinforced hard-walled hose on the...

    We use a wire reinforced hard-walled hose on the suction side of the system to make sure that it does not get sucked flat by the raw water pump. Our P/N is 845004. It is sold by the foot. Your...
  4. Replies
    10
    Views
    621

    If you close the sea cock at the water inlet, the...

    If you close the sea cock at the water inlet, the raw water pump will pull anti-freeze into the system and push it through the raw water side of the engine's cooling system. We would recommend...
  5. Replies
    7
    Views
    444

    If there is a chance of going below freezing , I...

    If there is a chance of going below freezing
    , I would not take a chance. There are only 4 drain points on the engine ... the line that goes from the raw water pump to the heat exchanger, the heat...
  6. Replies
    7
    Views
    444

    Anti-Freeze Protection Levels

    The new Raptor Engines are equipped with what is commonly referred to as a "half closed cooling system". This means that the engine block (including the heater) is cooled by anti-freeze and the...
  7. Replies
    4
    Views
    1,483

    Cleaning the filter screen on a 1:1transmission...

    Cleaning the filter screen on a 1:1transmission is not an easy task and is probably best left to your dealer. The filter is on the very bottom of the 1:1 trans and in most cases there isn't room to...
  8. Replies
    3
    Views
    1,442

    Re: Oil Pressure

    Minimum oil pressure at idle per GM Spec is 4 psi and 20 PSI at 2000 RPM. I suspect you may have a bad oil sender. I would heve my dealer temporarily install a mechanical gauge to verify the...
  9. Replies
    14
    Views
    2,914

    Who is your dealer? Is your boat there now? I...

    Who is your dealer? Is your boat there now? I would like to give them a call to see if I can give them soms assistance. Generally the throttle response on these engines is pretty sensitive and a...
  10. Thread: vapor lock

    by Engine Nut
    Replies
    14
    Views
    4,627

    Re: psi on secondary pump?

    The pump we are using is the HVLP pump that was used on the carbureted engines which is approx 6-8psi. The pump itself is easy but you also need to be able to tap into the existing fuel pump wiring...
  11. Replies
    6
    Views
    1,554

    This a message I posted a couple of weeks ago in...

    This a message I posted a couple of weeks ago in the Service ans Repair area. The information is still valid. We are not swapping out fuel pumps on engines.

    A little clarification. The issue we...
  12. Replies
    9
    Views
    2,041

    Re: Running out of water

    It is really much better to adjust carb with the boat in the water. You need to have some backpressure on the exhaust to get the carburetor dialed in properly.
  13. A little clarification. The issue we have been...

    A little clarification. The issue we have been seeing that is presumed to vapor lock is a condition that appears to be most prevalent on the 2007 model 340 engines with ETX CAT manifolds. The theory...
  14. Replies
    7
    Views
    1,554

    Re: cold start

    I PM'd you with some additional questions and info. Hope to hear from you soon.
  15. Replies
    7
    Views
    1,554

    Re: temp sender

    You changed the right one. That sensor is the one that communicates with the ecm on the engine to tell it what temperature the engine is. When it is cold, the ecm holds the fuel injectors open a...
  16. Replies
    7
    Views
    1,554

    Re: help ... poor cold start

    Your engine has two temp senders. Did you replace the one that has a two wire plug for the connector or the one with a single threaded stud connector. The two wire sensor is for the ECM and the one...
  17. Replies
    2
    Views
    1,115

    If the reason for the check engine light coming...

    If the reason for the check engine light coming on was low voltage and that issue has been resolved, the check engine light should go away after three complete warm up cycles. A warm up cycle is...
  18. Replies
    18
    Views
    3,074

    Re: Joining in a thread with same problem. A little help?

    Just a note to anyone posting for assistance with engine issues. Please let us know what engine it is you have as well as the model year of the boat. It helps us to know whether the engine is a...
  19. Thread: Oil Dump

    by Engine Nut
    Replies
    8
    Views
    1,662

    One end of the oil drain hoas attaches to a...

    One end of the oil drain hoas attaches to a special fitting at the bottom of the oil pan. The other end has a clip on it and it generally attaches to the engine lift ring at the front of the engine....
  20. Thread: Oil Dump

    by Engine Nut
    Replies
    8
    Views
    1,662

    Re: Oil Dump

    The 15W40 oil is correct even id it says for diesel use.

    The engine does not have a shut off for low oil pressure.

    Check the oildrain hose and the oil filter relocator and associated hoses.If...
  21. Thread: Starter

    by Engine Nut
    Replies
    8
    Views
    2,634

    As long as they are rebuilt to J1171...

    As long as they are rebuilt to J1171 specifications, rebuilt starters are just fine.
  22. Thread: Starter

    by Engine Nut
    Replies
    8
    Views
    2,634

    Re: Starter

    The Indmar part number forthe starter is S571006. If your dealer doesn't have one on the shelf, we can get one to him before the weekend.

    If you go elsewhere for a starter, make sure that it is a...
  23. Replies
    4
    Views
    1,336

    Re: Engine Issues 06' Moomba

    Is your engine carbureted or an EFI engine? The diagnostics are a little different.
  24. Re: 325 FI Hesitates when taking off under load

    Have the dealer check the fuel pressure and see if it drops off on acceleration. The nominal pressure is 60 PSI and shouldn't fall much below that on acceleration.

    Engine Nut
  25. Thread: Fuel ussage

    by Engine Nut
    Replies
    21
    Views
    3,640

    The 325 has 8 injectors, one per cylinder. I do...

    The 325 has 8 injectors, one per cylinder. I do not know the gph rating of the individual injectors and that really wouldn't be of great value. The ECM controls the fuel injector on-time in the...
Results 1 to 25 of 64
Page 1 of 3 1 2 3