Search:

Type: Posts; User: VA LSV

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. The actuators are hydraulic and fluid is pumped...

    The actuators are hydraulic and fluid is pumped from a power unit which has a small tank with an integral pump. Is your boat an LS direct drive or an LSV v-drive? The tank is located in the front...
  2. Replies
    1
    Views
    127

    Teleflex CH2200 looks like a good fit but check...

    Teleflex CH2200 looks like a good fit but check with these guys.

    skidim.com
    803-345-0996
  3. Replies
    44
    Views
    7,637

    Confirm you have 12 VDC to the solenoid. Swap...

    Confirm you have 12 VDC to the solenoid.
    Swap solenoids with 1 of the valves that is working.
    If you installed a new Orbit valve complete with the solenoid, check the voltage rating on the new...
  4. Replies
    12
    Views
    634

    In Virginia the minimum age to operate a PWC is...

    In Virginia the minimum age to operate a PWC is 16 and requires you to complete a boater course to receive a boat operators license. People can be annoying whether on PWC's or boats when they are...
  5. Replies
    6
    Views
    326

    The factory Gravity 3 ballast system should have...

    The factory Gravity 3 ballast system should have 3 switches below the throttle to control fill/empty of each bag. Stock rear bags were 250# and the floor locker 400#. Check that the fill valves...
  6. I switched to Irritrol valves when 1 of my Orbits...

    I switched to Irritrol valves when 1 of my Orbits failed and it did reduce my fill times. I didn't want to go the reversible pump route since I usually putter to the end of my cove while filling...
  7. Check that the manual override isn't on. It's a...

    Check that the manual override isn't on. It's a little black lever on the valve. Quick cheap fix would be to pickup a 3/4 irrigation valve from any home improvement store and swap it out. Factory...
  8. Replies
    13
    Views
    360

    Check with these guys. https://www.skidim.com/

    Check with these guys.
    https://www.skidim.com/
  9. Replies
    25
    Views
    1,219

    Blower in my '05 is located on the port side. ...

    Blower in my '05 is located on the port side. Remove the divider panels to get access. Invest in a wave shaper or build your own "suck gate". You can find plenty of specs on line. Easy DIY...
  10. Replies
    1
    Views
    121

    Check with these guys. skidim.com

    Check with these guys.
    skidim.com
  11. Thread: Wakeboard Rack

    by VA LSV
    Replies
    17
    Views
    7,144

    https://www.fluidconcepts.net/Wakeboard-Rack-Moomb...

    https://www.fluidconcepts.net/Wakeboard-Rack-Moomba-p/pf1.2-oval-ano-m.htm
  12. Replies
    11
    Views
    606

    Check the draft specs on the Moomba model you are...

    Check the draft specs on the Moomba model you are considering. Border line for sure plus sand would shorten the raw water pump impeller life.
  13. Replies
    1
    Views
    90

    https://www.skidim.com/prodinfo.asp?number=WAL49

    https://www.skidim.com/prodinfo.asp?number=WAL49
  14. Replies
    3
    Views
    148

    Check here skidim.com

    Check here

    skidim.com
  15. Thread: Stuck Prop

    by VA LSV
    Replies
    8
    Views
    449

    The prop is a taper fit to the shaft and...

    The prop is a taper fit to the shaft and shouldn't be lose. Sounds like your key has deformed since it was taking all the force and you will have to drive it out with a punch.
  16. Thread: Battery specs?

    by VA LSV
    Replies
    5
    Views
    254

    1000 CCA is pretty standard for marine starting...

    1000 CCA is pretty standard for marine starting batteries. What is the relay located and what is wired to it.
  17. Replies
    2
    Views
    396

    I'd be interested in the key fob but don't have a...

    I'd be interested in the key fob but don't have a need for the other items.
  18. Also these guys. www.skidim.com/

    Also these guys. www.skidim.com/
  19. Replies
    22
    Views
    2,190

    I used 1/4-20 SS set screws. Just snug them up...

    I used 1/4-20 SS set screws. Just snug them up against the boat brackets to take out any play and rattle. Use blue locktite to keep them in place and tight. Been working great for 10 seasons.
  20. Replies
    22
    Views
    2,190

    Got a look at my boat today and found I drilled...

    Got a look at my boat today and found I drilled and tapped the platform brackets, not the boat brackets.https://uploads.tapatalk-cdn.com/20190101/3513f7872da79b8ce32f9669166ce20d.jpg


    Sent from...
  21. Replies
    6
    Views
    697

    According to NGK the correct gap is 0.040". ...

    According to NGK the correct gap is 0.040".

    http://partcat.com/ngk
  22. Replies
    22
    Views
    2,190

    Forgot the link ...

    Forgot the link

    https://forum.moomba.com/showthread.php?30024-Surf-platform-wobble&highlight=swim+platform+screw
  23. Replies
    22
    Views
    2,190

    Here's a link to an thread that has a pic. Mine...

    Here's a link to an thread that has a pic. Mine didn't have the threaded holes so I had to drill and tap the bracket that is attached to the boat. I used 1 SS set screw per bracket. This was after...
  24. Replies
    22
    Views
    2,190

    I don't have a pic but will try to get one...

    I don't have a pic but will try to get one tomorrow. You drill and tap the bracket on the boat so the set screw pushes on the platform bracket that slides down into the bracket mounted to the boat. ...
  25. Replies
    22
    Views
    2,190

    After drilling new holes for the pins I drilled...

    After drilling new holes for the pins I drilled and tapped the bracket and went the set screw route to take out the play. I apply fresh blue Loctite every spring when reinstalling the swim platform...
Results 1 to 25 of 295
Page 1 of 12 1 2 3 4