Search:

Type: Posts; User: VA LSV

Page 1 of 12 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    15
    Views
    1,058

    I used 1/4-20 SS set screws. Just snug them up...

    I used 1/4-20 SS set screws. Just snug them up against the boat brackets to take out any play and rattle. Use blue locktite to keep them in place and tight. Been working great for 10 seasons.
  2. Replies
    15
    Views
    1,058

    Got a look at my boat today and found I drilled...

    Got a look at my boat today and found I drilled and tapped the platform brackets, not the boat brackets.https://uploads.tapatalk-cdn.com/20190101/3513f7872da79b8ce32f9669166ce20d.jpg


    Sent from...
  3. Replies
    6
    Views
    450

    According to NGK the correct gap is 0.040". ...

    According to NGK the correct gap is 0.040".

    http://partcat.com/ngk
  4. Replies
    15
    Views
    1,058

    Forgot the link ...

    Forgot the link

    https://forum.moomba.com/showthread.php?30024-Surf-platform-wobble&highlight=swim+platform+screw
  5. Replies
    15
    Views
    1,058

    Here's a link to an thread that has a pic. Mine...

    Here's a link to an thread that has a pic. Mine didn't have the threaded holes so I had to drill and tap the bracket that is attached to the boat. I used 1 SS set screw per bracket. This was after...
  6. Replies
    15
    Views
    1,058

    I don't have a pic but will try to get one...

    I don't have a pic but will try to get one tomorrow. You drill and tap the bracket on the boat so the set screw pushes on the platform bracket that slides down into the bracket mounted to the boat. ...
  7. Replies
    15
    Views
    1,058

    After drilling new holes for the pins I drilled...

    After drilling new holes for the pins I drilled and tapped the bracket and went the set screw route to take out the play. I apply fresh blue Loctite every spring when reinstalling the swim platform...
  8. Replies
    15
    Views
    1,058

    Mine had play in they when new due to...

    Mine had play in they when new due to misalignment which caused the holes to enlarge. Welded mine up and drilled new holes with the platform in place so that all the holes line up with new larger...
  9. Replies
    1
    Views
    111

    Original motor would have been a 350, not a 305. ...

    Original motor would have been a 350, not a 305. Prop rotation is not reverse like Nautique.

    Here's a link to a 1999 owners manual. ...
  10. Thread: Prop Puller

    by VA LSV
    Replies
    10
    Views
    622

    Prop Puller

    If you are looking to buy a prop puller I highly recommend this.

    https://propshopinc.com/wakeboard-ski-boat-prop-puller-kit-w-puller-prop-nut-prop-wrench-case-3-4-1-1-8-p828.html
  11. Add marine Stabil and you'll be fine. Run it on...

    Add marine Stabil and you'll be fine. Run it on the fake lake if you want for more piece of mind. This is what I have done for 13 winters.
  12. What year, model and engine? Newer models have...

    What year, model and engine? Newer models have the engine hours stored in the ECM. Is it a separate hour meter? Owner should be able to provide details. If not that would be a red flag.
  13. Replies
    5
    Views
    3,715

    I have a pair of racks from my 05 LSV and would...

    I have a pair of racks from my 05 LSV and would be willing to sell 1 set. PM me if you are interested.
  14. Replies
    4
    Views
    282

    Says 2-3/8 x 46-1/4 is original size. ...

    Says 2-3/8 x 46-1/4 is original size.

    https://www.greatlakesskipper.com/moomba-boat-ski-tow-pylon-107179-swivel-2-3-8-x-46-1-4-inch-stainless
  15. Oil pressure gauge should be standard. What...

    Oil pressure gauge should be standard. What gauges do you have on the right near the throttle? That's where the optional wakeplate and depth gauges would be and should be the only place where blank...
  16. Replies
    3
    Views
    208

    The original top and bottom gaskets were very...

    The original top and bottom gaskets were very thin and fragile so instead of replacing them I used RTV.
  17. Thread: Bad starter?

    by VA LSV
    Replies
    1
    Views
    121

    The clunk is the solenoid picking up so most...

    The clunk is the solenoid picking up so most likely the starter is bad.

    https://www.skidim.com/STARTER-BOTTOM-MOUNT-GM/productinfo/RF122015/
  18. Thread: Fluids look low

    by VA LSV
    Replies
    5
    Views
    264

    Check fluid levels with the boat at operating...

    Check fluid levels with the boat at operating temperature but not running.
    Go here and download an owners manual if you don't have one. https://www.moomba.com/resources/downloads
  19. Replies
    3
    Views
    249

    Sent you a PM

    Sent you a PM
  20. Thread: Fluids look low

    by VA LSV
    Replies
    5
    Views
    264

    That's the V drive in your pic. What year is...

    That's the V drive in your pic. What year is your boat? Add 30wt oil until the level shows good on the stick. Easiest way to add oil is remove the breather and use a small funnel. My transmission...
  21. Thread: EZ Cruise?

    by VA LSV
    Replies
    16
    Views
    4,356

    Check your throttle linkage. If it has throttle...

    Check your throttle linkage. If it has throttle by wire then yes Moomba EZ cruise would be compatible. If it has a cable all the way back to the helm then look at this
    https://www.hydrophase.com
  22. Replies
    3
    Views
    184

    The swim platform is very heavy and awkward to...

    The swim platform is very heavy and awkward to handle. Best to do this with the boat on the trailer. I still have the original black covering on mine. I scrub it every spring with back to black...
  23. Replies
    7
    Views
    458

    The cover on my '05 is like the one on ebay.

    The cover on my '05 is like the one on ebay.
  24. Replies
    6
    Views
    311

    Look for these ...

    Look for these https://www.irritrol.com/en/valves/700-series
  25. Replies
    7
    Views
    458

    https://www.ebay.com/itm/Indmar-Assault-EFI-Inboar...

    https://www.ebay.com/itm/Indmar-Assault-EFI-Inboard-Boat-Motor-Engine-Black-Fiberglass-Cover-Cowl-/132061263927?hash=item1ebf76f837
Results 1 to 25 of 277
Page 1 of 12 1 2 3 4