Search:

Nice looking Mojo.
Wife and I did the same thing this year.
2025 mojo to a 2025 mojo (left over). I haven't picked it up yet, waiting on better weather.

Good to know of the RGB lights. I can...

You are 100% correct that there should be 2 resistors.

I'm just saying in most systems the plugs or terminators will look the same.
Your troubleshooting is also correct. 120ohms is wrong and...

That makes sense.
The rear resistor is 2 prong which is the expected.

The green one in the front is 4 prong and normally not a resistor connection.

Do you have things not working correctly, or faults that came on?

Most times CanBus terminators are built into the device so things like this don't happen.

Do you have things not working correctly, or faults that came on?

Most times CanBus terminators are built into the device so things like this don't happen.

What sub do you have now?

I had a 10" sub under the helm just mounted to the wall. No box, no ports just free-air. Mounted like the 6.5 speakers.

I installed a sealed box and upgrade to a 12"...

For now, you could keep the firdt 6 channels of the JL amp on your 6.5 inboards. The other 2 channels you could bridge together. Positive from 1 channel and Negative from the other. This should...

Merry Christmas to all the misfits still visiting.

Enjoy the winter and be safe.

Alright Buckeye I'm sure you are going to get a lot of opinions but that is because there are so many options.

First, what do you have now in the boat? Yeah the 2-8" tubes, but what else?

I...

Just checking in and saying welcome back!

Not sure what happened with the site, but glad it is back to normal. I think a lot of us avoid FB and were locked out of the new site.

Also, I assume...

If you search the site you will find a bunch of setups.

I have a single 12 under the helm but mine is in a sealed box I built. I used the front panel as the face and added the box to it. I lost...

Finally, the old site is back. Sorry for thebsilence as I couldn't log in.

Good to hear you got things sorted out.
Would like to know if te new distributor fixed it and what sound is different....

At this point, I would use a normal sending unit adapter and skip the vee jet nozzle to get back on the water.

The sending unit adapter has a smaller hole than normal and creates a spray in the...

Not sure exactly which one will work for you.

GM block is typically 1/4NPT into the engine. The oil line is 1/4NPT with a reducer for the compression. The pressure sending unit is 1/8NPT.

You...

The part you are looking for is called

"Oil pressure adapter fitting"

Your engine is based on 1996 to 1999 GM 5.7 V8 engine. A similar adapter is installed on the trucks from this time.

You...

By now everything is most likely in the lake and gone. Just watch your temps and you are probably fine.

oil pressure sending unit tee.

Search this exact thing and you will find all kinds. You need to know the thread size and type.
1/4" NPT is typical for GM which is the basis for that Indmar...

My tractor has 2 fuel filters that I had to find the hard way. I had justt done the full service and had maybe 10hrs since then amd it died in the yard and wouldn't start. Found out there was a...

31119

This could be the problem for sure.

2008 325 Assault - carb or injected?

Ether runs rough all the time. Sounds like a fuel issue for sure if it did run on ether.

Weird it would bend like that without getting hit from the inside of the boat. That would quite a bit of heat to make it collapse like that.

I found a couple 24 SA demo boats but I have to travel. Since the 25 re-design they are willing to deal.

I really want an SL to match my MOJO size but thinking the SA isn't far off.

I found a...

Reading through other forums I found this.

https://forum.moomba.com/showthread.php?32150-Melted-hull-through-exhaust-leaking-water-replacement-parts-suggestions

Looks like you might still have...

I'm with you HAK on the new boat idea. The BOSS has even approved this!
I have found a few 2024 left overs and now 2025 left overs are coming around with deals. I have a plan to make this work, but...

I wasn't talking this step directly, but any steps on the platform. Just wondering how to attach correctly. That older, out of shape comment kinda hurt..... lmao