Search:
Type: Posts; User: bp3
Search: Search took 0.01 seconds.
-
08-02-2017, 11:26 AM
Thread: 2000 moomba kamberra set up
by bp3- Replies
- 14
- Views
- 5,693
I am not sure if its the same hull, but I have a...
I am not sure if its the same hull, but I have a 2000 mobius V. I run two 540 lb custom sacks from wake makers in the back and a 550 fat sack in the middle locker, and can surf just fine (with a...
-
05-23-2017, 02:13 PM
Thread: Prop shaft needed
by bp3- Replies
- 2
- Views
- 909
Thanks! Cecil hooked me up right away. Great guy,...
Thanks! Cecil hooked me up right away. Great guy, good prices.
-
05-22-2017, 10:06 PM
Thread: Prop shaft needed
by bp3- Replies
- 2
- Views
- 909
Prop shaft needed
I need a prop Shaft for a 2000 moomba mobius v. It's back order ed from factory. Any ideas?
-
04-06-2017, 12:43 PM
Thread: Sherwood P105 Raw Water Pump Bearings
by bp3- Replies
- 0
- Views
- 761
Sherwood P105 Raw Water Pump Bearings
Thought I would pass this information along:
The bearings for the pump are 6203RS, and can be found at the local bearing supply. -
04-03-2017, 11:58 AM
Thread: Steering mount loose?
by bp3- Replies
- 5
- Views
- 1,479
OK, so the rudder shaft is bent slightly and is...
OK, so the rudder shaft is bent slightly and is rubbing on the mount on the underside of the boat when turned one direction. Should it be straightened, or can a relief be cut into the top of the...
-
03-29-2017, 07:33 AM
Thread: Steering mount loose?
by bp3- Replies
- 5
- Views
- 1,479
Thanks, It looks like my rudder shaft may be bent...
Thanks, It looks like my rudder shaft may be bent slightly.
-
03-28-2017, 11:51 AM
Thread: Steering mount loose?
by bp3- Replies
- 5
- Views
- 1,479
25396 Where the black nut meets with the housing...
25396
Where the black nut meets with the housing with the 4 bolts. The nut is tight as is the bolt just visible on the back of the AL mount. I do not know if it is supposed to allow the mount with... -
03-27-2017, 03:27 PM
Thread: Steering mount loose?
by bp3- Replies
- 5
- Views
- 1,479
Steering mount loose?
Is this mount supposed to be loose to allow for movement of the cable? It is not loose at the floor, just where the black nut attaches to the aluminium mount.
25385 -
03-27-2017, 03:20 PM
Thread: what's this plug go to?
by bp3- Replies
- 6
- Views
- 1,871
Thanks Scott. Mine must just be a standard...
Thanks Scott.
Mine must just be a standard harness on with plugs for both the injected model and carb model. -
03-17-2017, 10:49 AM
Thread: what's this plug go to?
by bp3- Replies
- 6
- Views
- 1,871
Scott, Do you know if this is only used on...
Scott,
Do you know if this is only used on carbed models (my old 4.3 had same looking plug that was connected)? Current 5.7 is injected, and the harness is unplugged. Engine runs. -
03-15-2017, 04:24 PM
Thread: what's this plug go to?
by bp3- Replies
- 6
- Views
- 1,871
what's this plug go to?
2000 Moomba Mobius LSV - PCM apex 5.7 MPI25357
Results 1 to 11 of 11