Search:

Acme 2247 Prop. $400 plus shipping

Located in Tulsa
https://uploads.tapatalk-cdn.com/20200810/9c22bd661d77b7152af676bc49215980.jpg

Sent from my SM-N970U using Tapatalk

Great condition Hyperlite HiFi 56.

$300 plus shipping...

Mine has done this in the past and it might need to primed. My screen was actually off on the hull where I was able to put my foot up there and I could fill it suck and it started to suck water. ...

15 Supra SG 400
350 hours
New Gatorstep
New Rev10s with custom 12" wetsounds box
Swivel board racks
Boatmate trailer
Has all options I think except heater
Great condition

$80k

Could be 1450s but not positive. I do have a 15x12 prop. My X30 surfed so much better. Hope I can figure it out. With these small surf plates just don't know how well it's going to do

Sent...

I think the front now is 750 (it's a wrap around) and the rears look like 1100s

Sent from my SM-N970U using Tapatalk

Can you guys give me your advice on best setting for surfing a stock ballast 15 Supra SG? I feel like my wave doesn't have much push and small

Sent from my SM-N970U using Tapatalk

New impellers fixed it. Thanks for the help

Sent from my SM-N970U using Tapatalk

Just ordered some


Sent from my SM-N970U using Tapatalk

Well the look pretty good but maybe they are too soft now

Sent from my SM-N970U using Tapatalk

They are working just not sucking

Sent from my SM-N970U using Tapatalk

2015 SG

What all things should I check if my ballasts pumps aren't pulling water to fill my bags? I have checked the impellers and they have all fins and look to be in pretty good condition. ...

I have a '15 Supra SG and my screen does the phantom screen issue. Sometimes it will do things like I touch it even though I didn't or when I do touch it, it doesn't do anything. Anyone have...

I put Gatorstep in my boat so don't need this snap in carpet anymore. It came out of a 2015 but I know it fits many years. Also have the screw in snaps. $200 obo...

Which size did you get? Model number?

Sent from my SM-N970U using Tapatalk

I put a new triducer (transducer) in and I'm still getting 100 ft and it just stays there. Anything else I can track down?

Sent from my SM-N970U using Tapatalk

Thank you Larry!!

Sent from my SM-N970U using Tapatalk

Is there a write up on here on how to change the impeller on a 6.2 Raptor? I'm sure it's not hard but any tips to make it easier are encouraged.

Also what oil and filter are you using? Volume?...

I'm sure it's been talked about plenty, but I have the Raptor 6.2L, which has do I want to run? My options local are 87 no ethanol or 89 or 91 with ethanol.

Sent from my SM-N970U using Tapatalk

Looking for a 15 x 13 or something similar prop. Let me know if you have anything.

Thanks

Sent from my SM-N970U using Tapatalk

Thanks

Sent from my SM-N970U using Tapatalk

So is there anything special you have to do to install it since it has that key? With the MC you just stick it on. Also do you know what size key I need? Looks like it is a 1/4" x 2.5". Didn't know...

That key is bent. I assume it's supposed to be straight right? https://uploads.tapatalk-cdn.com/20200525/370bc61f65470fb8aa52b78bb8d2e3da.jpg

Sent from my SM-N970U using Tapatalk

I'm coming from a Mastercraft so used to a splined shaft, but wondering if this looks right? The key has grooved into the strut a little if you look closely....

You decide to sell these props again?

Sent from my SM-N970U using Tapatalk