Search:

Hi guys, thanks for all your help over the years. I just sold my 2015 Moomba Mojo and I’m always interested in what boats sell for, so I thought I would let you know that it sold for $64k with 535...

#FJB is what it means.

Okay, I have everything installed and was able to get on the lake this past Saturday. I watched this: https://www.youtube.com/watch?v=EKiSpHn1hug&t=739s pitch and roll video and got an awesome wave...

Is this still for sale?

Rural is the place to be!! When I retire I will move even more rural. I hate thieves as well OP! You just gave me another reason to like my Chevy Bolt (no cat). Too bad it can't tow the MOJO>

Great post, thanks! Do our Raptor engines get enough “better” mileage with non ethanol to warrant the change from e10?

Don’t gas stations have to label the pump as e85?

2 of the holes seeped all week, they are below the bag floor and there is no access to that area. I’m guessing there is somewhere for the water to go. If the bag leaks, it goes into the engine bilge...

I have the holes filled, I used the West Epoxy kit and the wires are ready to hook up. Getting that 502 off is a nightmare, it helped some getting an oscillating multi tool. That removed a fairly...

A leaking bag dumps into the engine bilge, ask me how I know 😂

That stuff is a PIA to try and remove. I don’t think it’s 5200, the spray doesn’t work on it. It’s some kind of thick padding that’s glued tight.

Rob says you just have to deploy both tabs for “launch” mode. Seems pretty easy.

The water is not in the bilge, it’s in the sub floor under the bag compartment, I’m not sure if there is a path...

Redrilled holes and below is the result.
30059

30060

Since I had to change the location of the actuator feet, I asked Rob what angle the tabs should be at when deployed? He said that 10-15...

The holes are in a great place for the tab, I’m wondering what is below the floor where the bags lay? I’m wondering if I can drill a hole a fish the wire up? It’ll be hidden behind the carpeted panel...

I got the blocks off with the marine debond suggested by Parrot (many thanks) , it took about 10 minutes per side. I sprayed the debond, let it soak, and then used a spatulas on the top/outside of...

Well, I went with Evolution because of price but also because Rob did an excellent job answering all my questions and I felt comfortable with him. He has YouTube videos on tab install and electrical...

Yes, it has the manual tabs and I want the plates next to the center plate like they make them now. I also want control in the cockpit.

Stuffs pricey but looks like it’ll make the job easier, thanks.

Sorry, the surf plate, I think it’s auto flow? The big block of metal on the transom port and starboard. I’m installing Evolution tabs and want remove those plates.

I have all the bolts and screws out, does anybody know of a good way to get that plate removed from the back of the boat? I tried a heat gun to heat up the epoxy and a hammer and that didn’t make it...

I'm going to try these and and see how they work.

https://www.amazon.com/SIOTI-Tether-Lanyard-12Inch-Session/dp/B073PV51NW/ref=sr_1_1?keywords=sioti+cable&qid=1584624675&sr=8-1

I have a 2015 Mojo and the pin holder for the swivel rack finally gave up and broke. It’s that rubber piece that holds the pin so it doesn’t fall in the lake when you pull it out of the wakeboard...

They have an impeller puller on sale if anybody is wanting one.https://www.bakesonline.com/impeller-puller-stainless-steel.html

That's what my dealer said at 300 hours, you don't need to change the plugs. Of course, my dealer is pretty inept.

IF those are Fly Highs they do, mine is a 2015 and they are fly highs.