Search:

Type: Posts; User: vdubnick

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    86

    easy... hook up a buzzer or included siren to...

    easy... hook up a buzzer or included siren to give the audible chirp when button is pressed.
    https://www.amazon.com/Directed-Electronics-Powersport-Waterproof-Watercraft/dp/B07C5Y8ZGG

    flow 3...
  2. Thread: Cooler set up

    by vdubnick
    Replies
    124
    Views
    7,534

    on mine there is a panel/wall with the front...

    on mine there is a panel/wall with the front pump(s) mounted to it, ballast is on other side, if the pumps were moved, there would be plenty for the batteries in their boxes. otherwise the battery...
  3. Replies
    2
    Views
    86

    use keyfob for surf switch

    anyone wireup a keyless entry fob, or basic wireless 12v switch to allow surfer to switch sides without timing it out with the driver? its next on my mod list.
  4. Replies
    22
    Views
    233

    i would say so, im not sure what tolerance they...

    i would say so, im not sure what tolerance they have, but quick measuring with calipers i got a solid 1.13"
  5. Replies
    22
    Views
    233

    ok, my assumptions about the actuators being a...

    ok, my assumptions about the actuators being a "special" non-catalog model for moomba was correct.

    per Lenco, specs for the 9L HP 4 actuator are:
    12 volt - 2.5 normal to 20amp max – 1.25 inch...
  6. Replies
    48
    Views
    3,401

    ha, thanks for the tips. Im sure the pressure...

    ha, thanks for the tips. Im sure the pressure concern was due to a connector that was loose or poorly fitted. unless the overflow is plugged there is zero pressure other than the pressure head from...
  7. Thread: Cooler set up

    by vdubnick
    Replies
    124
    Views
    7,534

    yeah, i really have to crush my cans or i fill...

    yeah, i really have to crush my cans or i fill the trash within the first hour hahaha.

    There is almost enough room to move the batteries side by side towards the bow, and leaving the full opening...
  8. Replies
    48
    Views
    3,401

    good to know on the fill time. mine is set to...

    good to know on the fill time. mine is set to 6:30, and only the bow bag overfilled. So I need to do some adjusting.

    I was torn paying extra for the bins knowing i could potentially get rid and...
  9. i think so, i havent confirmed, but when i was...

    i think so, i havent confirmed, but when i was running some wires and tightening the tower nuts i noticed 4 sets of speaker wire going to the tower (EIA colors)
  10. Replies
    48
    Views
    3,401

    measured mine last night, 10" deep

    measured mine last night, 10" deep
  11. Replies
    22
    Views
    233

    totally... i am a Mech E. so i get it. it just...

    totally... i am a Mech E. so i get it. it just bothers me that the screen (0-100) does not match end to end in physical form. I am fine with the travel, or lack thereof if that is how it was best...
  12. Replies
    22
    Views
    233

    just overanalyzing the tab... the engineer in me...

    just overanalyzing the tab... the engineer in me gets hung up on the details.
  13. Replies
    48
    Views
    3,401

    interesting , i will measure mine tonight, they...

    interesting , i will measure mine tonight, they dont seem as deep, but maybe they are.

    side note, do yours catch the vinyl/cover? i had to round off the sharp edge on mine because it was...
  14. Replies
    48
    Views
    3,401

    the bins are pretty shallow (about 6-8"). i...

    the bins are pretty shallow (about 6-8"). i think the 22 models have "upgraded" bags, as mine fill under the seats all the way, and appear to fill the lockers up to the shallow storage bins.
  15. what is the software version again? mine is...

    what is the software version again? mine is currently MoombaBP_MY22_47740_20210708
  16. Replies
    22
    Views
    233

    mine goes 0-100 on screen as well, it is just...

    mine goes 0-100 on screen as well, it is just that the physical travel is only 0-70 or 100-30 depended where you start.


    also, noticed that the surf plates max out at 90, but the manual...
  17. Replies
    22
    Views
    233

    ok, actuator measures 10in, and seems to be a 101...

    ok, actuator measures 10in, and seems to be a 101 XDS model, but the branding is 9L HP 4 on all 5 actuators. not listed on lencos sheet so it may be a custom config with reduced actuation.

    mine...
  18. Replies
    22
    Views
    233

    found lencos catalog, looks like they have 2...

    found lencos catalog, looks like they have 2 options for travel, 2.25 and 4.25, im going to go measure and see

    http://www.delzer.com/oneasg/lenco/36/
  19. Replies
    22
    Views
    233

    honestly better off trying the GSA style, and add...

    honestly better off trying the GSA style, and add some fins to the tabs to help direct the water out more. ultimately though, the basic dimensions of the wave are all based on displacement and...
  20. Replies
    22
    Views
    233

    ok, so figured out that the settings button...

    ok, so figured out that the settings button works, i was just not pushing hard enough. They used a thick rubber button to push a tactile switch, so there is subtle click when pressed hard enough.
    ...
  21. Replies
    22
    Views
    233

    thats what i was thinking... the main WP is my...

    thats what i was thinking... the main WP is my main concern, not sure if its a calibration issue, or if the actuator is bad
  22. Replies
    22
    Views
    233

    also noticed the settings (3 lines) button is non...

    also noticed the settings (3 lines) button is non responsive... i dont think the boat needs to be running for it to work?
  23. Thread: Cooler set up

    by vdubnick
    Replies
    124
    Views
    7,534

    great to know

    great to know
  24. Replies
    22
    Views
    233

    wakeplate travel and flow 3.0?

    playing on my boat in my shop last night, decided to take a look at the wakeplate travel, more out of curiosity, as i wondered if you could accidentally flip surf on and damage the plate on the...
  25. Replies
    19
    Views
    346

    on the plug side. there should be supply voltage...

    on the plug side. there should be supply voltage when the ignition is on to energize the coils in the alternator. is it a single or two wire plug?
Results 1 to 25 of 70
Page 1 of 3 1 2 3