Search:

It is that ethanal gas. I have had the same problem the last three years. I have talked to other boat owners. They are having the same problems. You need to drain the carb bowls an flush gas out of...

The oem has mechanical secondaries and the other one is vacumn secondaries. The oem is a 4150 an Skidim recomends the 4160 which is the vacumn secondaries. That is the only difference. That is why...

Has anyone changed from a duel feed carb to a single feed carb ? I can buy a single feed 600cfm for $428. Where a duel feed is a $525. Does anyone have any comments about this ? Any an all comments...

Yeah I fiqured out how to take it off... I even found the bearings at NAPA... But the seal is a whole different story... The bearings were $10 doallors a piece... Everywhere I called they all said...

Thanks... I have a 99 outback... So I think it is a little different... What I am thinking is the housing and bearing are sealed and pressed on the crank shaft... If i can get it off without breaking...

Has anyone every replaced the bearings in the impeller housing? The bearing is leaking out the back of the housing. So before I pull the housing with a bearing puller. And replace it. I was just...

Believe it or not.. I used TILEX mold and mildow remover... It worked really great... But I also had a spray bottle of water to remove all the TILEX... Since it had caustic in it... It didn't get all...

Yeah now EVERYONE has to chip in on gas... I use to let people slide... Now it is money up front... Because I try to keep the tank full... So people would get on and say if I need gas they would...

I have a stereo problem or ignition problem.... My stereo works with key in off position... But when I put the key in the on or start position... Stereo doesn’t work anymore... So I need some new...

My friend was saling and I was buying... I have a '99 outback.... It has been a great boat... No problems with it in the last 3 years... I bought it at the very end of the season.... It had less than...

I did a search for wakeboard size... I found a lot of info... They told me everything I needed to know on wakeboards... Size, bindings,fins, length, rockers,width, design, etc.... It was well worth a...

Over a 150 hours a year... Use it or lose it.. And YES gas is high... But the stress reliever the boat is... It is worth every dollar.... And the booze cruise late at night.... It is well worth the...

Hey guys... I bought a used '99 outback... It looked great and drove great.... I bought it two years ago with a 147 hours on it... I have put over 200 hours on it... And all I have done to it is tune...

I have a '99 outback... I have a 4 blade prop.... It is 13 X 13... If I am not mistaking... I had a really hard time getting it off... I bent the tips when I hit something in the river... I had to...

Fishing boat is called " BITE ME "

Ski Boat is called " EAT IT " Because that is what happens most of the time... Someone eats it when they are trying to show off.

Yes it does.... This is the first time to own a ski boat... So I didn't know about the impeller... Now I do... So I WILL keep an extra one on hand.... I am thinking of just going ahead and replace...

I have a 99 outback. 310 hp, carb engine.
Ben

I went in shallow water and sucked up some silt... The motor over heats.... I searched to find out if I need to replace the water pump... All I can find is info on the impeller.... So I guess I am...

I bought a 99 outback 2 years ago... It had 147 hours on it... I have put 124 hours on it since.. All I have done was replace the fuel pump, plugs, trans fluid, belt, fuel filter, that is about it......

Thanks guys for the help... I did mark the nut and counted the turns it took to take it off.. So how hard is it putting it back on? The prop that is... To get it back to the right spot?

I am trying to remove the propeller... I don't want to bang on stuff... So do I need a puller? And if so what kind and where do I get one... Any and all help would be great... Thanks guys for the...

Just be glad it was a ski rope... I live on a river.... Where barges go up and down... I caught about a 8 foot piece of 3/4" yellow nylon rope on the prop and shaft.... Oh yeah you come to a quick...

I have an '99 outback... It has a gray rubber on the platform... It looks good and no smudges... But the fins fron the wake board does nick it.... Other than that I like it... The gray and blue looks...

Did you try pushing the reset button above the switch?

I have a 3 car garage... It is 24 ft deep... I have a '99 outback... With out the swim platform on the boat.... And no swing away tongue... I have about 3 to 4 inches... But you have to be careful......