




Type: Posts; User: Moombas
This was taken off of my 2023 Moomba Max, fits the A3 Tower.
This includes the whole enchilada
Mounting bracket/arms
Bimini frame
Oem bimini and zip cover
In basically new...
https://www.ebay.com/itm/116287579480?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=onRTaqnNSpK&sssrc=4429486&ssuid=onRTaqnNSpK&var=&widget_ver=artemis&media=COPY
Yea, no need for 7" screen though, maps are also available on 2017+ Moomba's with the HV480 or the HV700 screens. https://www.moomba.com/wp-content/uploads/2021/08/2017-moomba-owner-manual.pdf page...
Looks like you need the zero-off GPS puck and the navionics usb dongle https://waterskis.com/gps-navigation
I am lookin at helping a friend add GPS Maps to a 2017 Craz, I am wondering if a cheaper 4 wire antenna could be tapped in to work.
I think that with boat prices continuing to rise, it will open the market for more budget wake boats similar to Heyday (even though heyday are junk) that don't have surf systems and could use some...
This prop rocks so far, I was able to add some lead back for a total of 800lbs of lead + my 5,500 lbs of water ballast. I am holding speed either side at around 9* pitch the wave is amazing. I can...
The plug under the dash is 2 pin, and wired to the RGB switch. The LED strips in the boat are RGB strips but the wire that runs around the boat is only 2 wire if you do not have the RGB option.
...
Intex has a new USB pump, looks kinda cool - https://amzn.to/4c10AWu
Here is the standard USB pump I use - https://amzn.to/4bZZXfV
I have 1,345 lbs wakemakers rear bags, factory subfloor bags under each side bench seats (500lbs each side), factory center bag 1,000lbs and the wakemakers 860lbs bow bag = 5,500lbs of water ballast....
It's pretty common when you're at the edge of a prop that you struggle to hold speed on the regular side.
So basically at my current weight I have to deploy some wake plate to bring bow down to...
Yea I think we actually end up surfing at 8.5-9* pitch on goofy side and its an insane wave.
The problem was the regular wave I couldnt get over 7* pitch, wake9 says 9-9.5* pitch is the best wave...
15.5x14 is not enough prop if you are running at the target pitch of 9.5*-11*
I tried a 3407, (15.5x13) it would pull the weight but when pitch was 9* or more I was at 4400 RPM.
I currently...
Thanks for the reassurance, just spoke with Jim, 3591 inbound and sending my 3407 back because I was surfing at 4400 rpm which was awful.
Now I have talked to 4 Moomba owners that have no prop...
I've now spoken to 3 gentlemen with Moomba Max's that run 16" prop and have been for a few years with no prop burn.
2 of them are running the ACME 3337 and one of them is running the OJ 963.
...
I was chatting with ACME about 16" props for the 1.76:1 transmission. I have a 23 moomba max and have been struggling to find the right 15.5" prop for all my ballast. I have talked to a few guys that...
This is a very interesting topic to watch unfold. I already hate that Malibu fit and finish has gone downhill since going public and now this.
Any chance you have these videos posted elsewhere? The youtube links are dead. I finally figured out why the seats don't open all the way, you'd have to notch the fiberglass to move the hinge further...
I now understand why no one has been able to get hinges to work with full range on a Moomba Max. After looking at moombas with factory hinges at the boat show they have a cut out around the hinge in...
Update my 2023 Max had RGB led strips on both side pockets and the REV 8's.
The Rev8's were pre wired and ran down the star side tower leg. I ran RGB wire to both side pockets and tapped the REV...
HFarr, it looks like where the hinge mounts to the bottom of your seat is at the very edge. The screw closest to the edge of the seat, does that screw into the vinyl lip?
Hey,
I had my dealer look up the ITC controller its $860, I am wondering how it plugs into your boat, does it use a 4 pin deutsch connector to communicate with the MFD or a 2 pin? I am trying to...
Sold my 2014 Mojo 2.5 to some friends so got to take a few pictures with my new and old boat :)
My new 2023 Max with fresh tint.
30930
30931
I was looking at the Makais and their seat seems to open just a litte further. I am going to order the OEM Moomba hinges and use the same cross member design you used. It looks like some Malibu boats...
I have been looking for NMEA 2000 answers as well. I believe the factory ITC RGB controller may interface with the screen via NMEA2000 which would make it easily addable to control the RGB via oem...