Search:

I noticed that on new Moombas, the "E-Z Cruise Speed Control" is an option. Is this available aftermarket, and if so, is it more economic than PerfectPass? Does it integrate (or offered by) with he...

Update: I've attempted resetting the "Black Box" by leaving the battery-leads disconnected for hours. I tried re-seating the connections to the "Black Box", as well as checking ground. No luck.
...

Hi qb12,
Thanks for the reply. I didn't turn these posts in my search, but I'm probably using the wrong keywords. I turned up most posts under 'fuse' and 'dash' - is there a better search term?
...

I have a 2000 Kanga/Outback model. This week, my dash just died -- every single gauge. My switches still work (Bilge, Lights, etc), and the engine runs fine; however, none of the gauges move.

If...

I had come up with a similar conclusion as FlaMoomba; consider that because your boat does not sit evenly, the lift will already have to be at least a couple inches further down than if you were...

Hi Smoke,
The choke plate is wide, wide, wide open -- and is always open because I have the choke set not to close unless extremely cold. The choke definitely isn't restricting any air movement,...

Thank you, Smoke Dog.

1. No friends with ski boats (if I did, I think I would get rid of this nightmare and pay them for co-use of theirs -- I'm beginning to realize I wasn't meant to own a boat)....

Hi all,
On my 2000 Moomba I have the Vortec 350 with the stock Holley Carb (4150 style), Holley P/N 75021-1. I had a minor leak from the accelerator pump and thought it would be a good idea to get...

I had come up with 16" on my Kanga, to clear the prop -- which is more of an issue than the fins.

There are a bunch of GPS options available. My waverunners were recently stolen (and they weren't insured) and I've done a ton of research on the subject. They make lo-jack style GPS systems that...

While on the subject of the Holley v. Edelbrock carbs, does anyone know if the Edelbrock marine carb is comparible to the Holley? For example, I believe the Edelbrock marine carbs have * Vacuum...

Thank you both.

I am going to check the prop and let you know how much pressure I have to put on it to get it to move. I also have to feel the shaft packing nut to let you know the temperature...

Thanks again Buttafewcoe-

I'm definitely not concerned with getting more top-end out of the boat, or the specific RPM to which it revs. My *only* goal is to be sure that everything is running...

That does help -- and confirm my original experiences, thank you.

Assuming the engine works fine (which isn't entirely true, but assuming for now). Is there any reason why I could have exessive...

Hi Pickle,
I've read really good things about the Edelbrock Marine carbs myself. I have a slightly off-topic question for you. In a separate thread I'm attempting to determine what the max RPM is...

Thank you Buttafewcoe & zabooda.

I have the straight shaft. I believe it previously maxed at 5,200 RPM before the new engine; now I'm maxed out at about 3,900 - 4,100. Buttafewcoe, you mentioned...

Thank you for the reply, Smokedog. I'm a bit confused by some of the content in your post and I'm hoping mainly to find answers to the two main questions, based on other people's experience here. I...

To Buttafewcoe -- thank you for the confidence booster -- I may give that a try if the upholstery companies are so busy I can't get a decent quote (which seems to be the case so far).

To Zabooda...

Doing everything I could to restore my Moomba after an overheat/engine replacement (it only had 90 hours usage prior to this), I took a long breather -- and just returned to the task. I have two...

I definitely would *not* go with teak. Had it on my last ski boat and glad to be rid of it. I don't believe there is still an issue with the swim platform decking; however, in my case I have the...

I have a similar problem and found what I believe may be a really good solution:

http://www.seadek.com/PageProj06SwimPlat.html

I haven't ordered it yet, but the person from SeaDek (Chuck Yates...

I believe the anti-siphon valve is the very small "check-valve" style connector that attaches your gas hose (from the fuel pump) to the gas tank. On my 2000 Kanga, it is directly behind the back...

I have a 2000 Kanga (very similar to the 2000 Outback but with a closed bow) and I'm trying to re-assemble the floor panels I had out while replacing the engine. For the life of me, I can't put...

Is there a way to order upholstery skins from Moomba, to replace skins that have been damaged? If I can't buy from Moomba, is there an alternative to "your closest Moomba dealer" with whom I've...

Hi Keaton, Catdog-
Yes, I did use the Indmar timing gears and chain, which is a roller style chain. I was forced to use them because the Indmar roller cam is a style of a different year than the...