Search:

I went with kicker 8 and 6.5 in krypt cans. cant see it very well but the factory holes in flat plate between the tubes on tower matched with the holes in new cans, wires run through centre of mount...

I picked up 300lbs from Wizard lake marine in Calmar.
Drift weight Canadian made in Drayton valley I believe. but its flat plates not shot.

Sent from my SM-G950W using Tapatalk

Had the knocking noise last year, put on fresh air exhaust over the winter and now the noise is gone.

Sent from my SM-G950W using Tapatalk

Did you confirm it is wake plate? I only managed to confirm it was plate by reaching under and holding plate with engine running.
We found the the sound really traveled, even noticed it when putting...

Hello and welcome

We have a 16 Craz and similar to you went from a I/O to a wake boat with never been on one or surfed before.
At the time there was no auto wake so can not really comment on...

sorry probably cant help you then mine is a 16 craz and thought they would be same but all mine are labeled but one Acc.

Sent from my SM-G950W using Tapatalk

I may be able to help as I traced my auxiliary switch wire yesterday but would like to confirm switch location before I steer you wrong?

Sent from my SM-G950W using Tapatalk

oh sorry but I knew for sure that both yellow and red was on ignition switched because both were crimped into same pin in factory harness, actually took harness plug apart to remove them.

Sent...

I was not concerned about voltage going to head unit rather that the yellow should be on 12 volt constant not switchable. After I moved the yellow to constant the head unit certainly starts up much...

I am in the middle of switching the head unit ignition wire to an accessory switch but found both the yellow +12volt and red ignition +12volt wire going to same location on the factory harness, I...

I picked up some from Wizard Lake marine in Calmar believe it's called drift wake weight and think they are out of Drayton Valley. but it's a couple of flat bar in a bag not shot.

Sent from my...

I believe they are rivets, easy to remove just drill them out, probably something to do with screws shearing.

Sent from my SM-G950W using Tapatalk

yes you bet. it's our go to lake we live in Leduc so only about 30 min away. Nice and deep and wind usually does not affect it as much as larger lakes.

Sent from my SM-G950W using Tapatalk

Ice off the lake two days ago so got out for the first time this season it was cold at 45 degree water temp but had the lake to...

The loose one is the impeller that came out of a 16 Craz the package is the impeller that I got from wakemakers not sure on gasket as it came with a new...

+1 For Chevy 1500
17 with 6.2 and air bags to eliminate squat. Switched from 3500 Duramax due to daily ride quality.https://uploads.tapatalk-cdn.com/20180219/d54c85e08c94d50f6170b1925f902bd8.jpg
...

Could i please get the code.

Thanks

Sent from my SM-G950W using Tapatalk

First surf style board Phase 5 Race used Model X...

here is the page from instructions, best you can get is blue whitehttps://uploads.tapatalk-cdn.com/20170731/84695923e243770e39dd5e6dca5064d5.jpg

Sent from my SM-G935W8 using Tapatalk

I would be curious to know if the fabric has changed or just the frame, if it was just the frame I am sure the cost would not be to bad.

Sent from my SM-T330NU using Tapatalk

What I did was take the vent line from the 1100 and run it to bottom fill on 400 then put a new vent line from top of 400 to check valve then to vent on boat, check valve is to help empty the piggy...

I went with Kicker aswell pair if 8 and pair of 6.5 in the cans i believe have been mentioned the 8s i did not use clamp just bolted in factory holes. I did have to trim the opening a bit took about...

the stock one's are often glued in bag and can be a problem and possible damage to remove.

Sent from my SM-G935W8 using Tapatalk

Being in Canada have you tried Shuswap ski and board they have Fly high 1100 lb bags for $249 CAD each.
You would need fittings and pannel savers as well

Sent from my SM-T330NU using Tapatalk

I am wondering the same thing just got my bow filler for a 16 Craz. When the parts guy gave me the hardware I asked him what it was for , he was not sure as it was new to him a as well but something...