Search:

Type: Posts; User: gregski

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    341

    I have two concerns with putting it into gear...

    I have two concerns with putting it into gear while on the trailer but I would be OK doing this as long as you are careful and aware.
    1. The cutlass bearing will be dry/un-lubricated. You can engage...
  2. Replies
    10
    Views
    330

    It's a float sensor so the fundamental problem is...

    It's a float sensor so the fundamental problem is that the fuel is moving around due to the boat's roll and pitch; a more accurate sensor doesn't change that. Mine moves as much as a 1/4 when in an...
  3. Replies
    11
    Views
    295

    That's silicone lubricant, not silicone sealant....

    That's silicone lubricant, not silicone sealant. It would be a better choice than a petroleum based lubricant (like Vaseline) but it's probably a moot point for this application. I also find that...
  4. Might not be the same. As far as I know, GM TBI...

    Might not be the same. As far as I know, GM TBI is around 15psi, not the much higher pressure used in multi-port FI but all fuel injection got dubbed "high pressure" because pressure for carbs was...
  5. Oh yeah, it doesn't make sense that wires for the...

    Oh yeah, it doesn't make sense that wires for the light would be on both side.
  6. I'd guess the two small wires are for the...

    I'd guess the two small wires are for the all-around nav light.
  7. Replies
    3
    Views
    209

    In my experience, the transmission cooler screen...

    In my experience, the transmission cooler screen has always caught any bits. I always have a little bit of fluctuation. I notice more fluctuation at first, like the thermostat doesn't open right away...
  8. Sounds like you're on the right track. Can you...

    Sounds like you're on the right track. Can you get the deploy angle to 0 degrees? That's the sweet-spot for me, 11 was definitely too much.
  9. Send him the picture and find out. I think that...

    Send him the picture and find out. I think that GSA works just fine with >95% of boats so his first reaction is "it should work ok". When I talked to him, it took a bit for him to remember the...
  10. Replies
    5
    Views
    258

    Are you looking for a functional repair or an...

    Are you looking for a functional repair or an aesthetic repair? Marine-tex epoxy is great stuff for filling/repairing holes and would be a great choice for a functional repair. It comes in white and...
  11. Replies
    23
    Views
    1,113

    A few more bells and whistles, rack and peanut...

    A few more bells and whistles, rack and peanut steering and you'll have re-created The Homer.
  12. Agreed, I actually found it easier to use...

    Agreed, I actually found it easier to use trigonometry. I taped a string to the hull up front, pulled it tight and then tied to something behind the boat right at the height that it touched the...
  13. On my first "just use the template" attempt, I...

    On my first "just use the template" attempt, I got an acceptable stow angle but it wasn't tight to the swim deck and the deploy angle was greater than 18 degrees or whatever which was what the...
  14. Replies
    9
    Views
    185

    I was operating under the assumption that the 21V...

    I was operating under the assumption that the 21V was the same hull but it is slightly different. If it's vertical (not sloped back at all) and the mount lands on a flat part, then it could be a...
  15. Well, on my first attempt, I held the template...

    Well, on my first attempt, I held the template up, drilled holes, attached everything and was ready for water in about 4 hours...
  16. Replies
    9
    Views
    185

    Upon closer inspection, I think sandm is right...

    Upon closer inspection, I think sandm is right and the hulls are very similar but just slightly different. The LSV transom is a bit recessed for the exhaust and trim tab, like MJHSupra's SSV but the...
  17. It's going to get ugly. If you are the type...

    It's going to get ugly.

    If you are the type who has access to a machine shop, likes to make custom, precision parts for your projects and writes custom firmware/software for other projects (at...
  18. Replies
    9
    Views
    185

    Yes that's the same hull/transom. There is enough...

    Yes that's the same hull/transom. There is enough stow room. When we are slammed, the swim deck and tab are dragging a bit but it's not really a big problem. If I had it to do over, I would raise the...
  19. You don't have to use a bucket of water to test...

    You don't have to use a bucket of water to test the power and float switch. The bilge pump has a little knob that you turn to test it. The knob is attached to the float so it's the same as using...
  20. Replies
    9
    Views
    185

    I think the 21V is the same hull as the LSV...

    I think the 21V is the same hull as the LSV started using in '06. I installed GSA on our '07 LSV. I've been meaning to write a bit of a review/story so I finally did:...
  21. Go Surf Assist / WaveControl system on '07 LSV: Love it but not recommended

    Summary: I installed the WaveControl system (same as Go Surf Assist but bought from WakeMakers) and installed it on our ’07 LSV. We love it, but BE WARNED: GSA told me that their kit cannot be used...
  22. Replies
    36
    Views
    1,537

    I agree with all that, but my post was really...

    I agree with all that, but my post was really meant as a bit of a joke: The irony of costanza's post was perfect in this thread.
  23. Replies
    36
    Views
    1,537

    Mods also get to clean up posts to the wrong...

    Mods also get to clean up posts to the wrong thread.
  24. Replies
    44
    Views
    7,746

    No, it just creates a magnet to pull the solenoid...

    No, it just creates a magnet to pull the solenoid plunger. (Technically, the magnet polarity would flip with the electrical current direction but that doesn't matter when attracting ferrous metal)
    ...
  25. Replies
    43
    Views
    1,659

    I'm 100% sure that I do not have a Ford, so like...

    I'm 100% sure that I do not have a Ford, so like I said "I'm not getting paid by GM".
Results 1 to 25 of 190
Page 1 of 8 1 2 3 4