plug and play with reversibles, reprogram the fill time to about 8 minutes before using and you should be just fine.
Printable View
plug and play with reversibles, reprogram the fill time to about 8 minutes before using and you should be just fine.
There you go!
How do you reprogram the fill time?
Do you have the Moomba EZ cruise or Moomba Digital Cruise Pro?Quote:
Originally Posted by KEH
If cruise pro:
http://youtu.be/0b0Q1dhRqBU
If not let me know. I have a document for the EZ Cruise style as well.
2009 LSV so I'm pretty sure it's the Perfect Pass Wakeboard Pro
Looks pretty similar to the one in the Youtube video but I am not near my boat to be able to confirm...
Either way, who knew!
All this time I have been cycling the darn switch...duh
on 2009, I think it's a bit more complicated and there are some steps you have to go through with the switches they blink on/off to indicate what you're doing, etc. check the archives for your owner's manual and you may have to reach out to SC.Quote:
Originally Posted by KEH
Very complicated IMO. So much so ive yet to do it
2009 Ballast System Programming
To change the fill time of the ballast:
1. Connectbatterytothewiringwiththe60ampbreaker.
2. Disconnectpowertotheballastcontrolboxbytrippingthe 60ampbreaker located by the battery.
a. This will have to be done for programming each ballast control box. (Left rear ballast, Right rear ballast, and Front ballast)
3. Resetthebreaker
4. Within5secondsofresettingthebreaker;toggletheballa stswitch(ofthefilltime you want to change) FILL-OFF-DRAIN-OFF- FILL-OFF
a. StopwiththeswitchtoggledtoFILL.
b. Thiswillenterballastcontrolboxintoprogrammingmode.
c. When the ballast control box goes into programming mode the
pump will quit turning on.
5. TheLEDontheballastswitchwillblinktoshowcurrentfill time.
a. Whencountingblinkswaitforthesecondblinkcycleaftert he
pause, blinking starts as soon as reprogramming has started and it
is easy to miss the first few blinks.
b. Refertothetimingcharttodeterminethecurrentfilltime basedon
the number of blinks.
6. ToADDTIMEtothefilltime
a. To add 30 secs, turn ballast switch to FILL then OFF.
b. NumberofblinkswillincreasebyoneeachtimetheFILL-OFFis
toggled.
c. Add remaining number of toggles of FILL - OFF to get the desired
number of blinks from the timing chart.
d. End with the switch toggled to FILL to count the blinks.
7. ToREMOVETIMEfromthefilltime.
a. Toremove30secs,turntoOFFthenDRAIN
b. NumberofblinksdecreasesbyoneeachtimetheDRAIN-OFFis
toggled.
c. Add the remaining number of toggles of DRAIN - OFF to get the
desired number of blinks from the timing chart.
d. End with the switch toggled to FILL to count the blinks.
8. Whencountingblinkswaitforsecondblinkcycleafterthep ause,blinking starts as soon as reprogramming has started and it is easy to miss the first few.
9. Whencorrectblinksareobtained,switchtoOFFandwait10s econdsto allow program to be set. This will now be stored in the AI unit.
Sent from my iPad using Tapatalk HD
TIMING CHART
Blinks
Time (minutes)
Blinks
Time (minutes)
1
2
14
8.5
2
2.5
15
9
3
3
16
9.5
4
3.5
17
10
5
4
18
10.5
6
4.5
19
11
7
5
20
11.5
8
5.5
21
12
9
6
22
12.5
10
6.5
23
13
11
7
24
13.5
12
7.5
25
14
13
8
ETC
20 max
Rear bags – All boats = 4.5 minutes of fill time = 6 blinks LS – split tank = 2 minutes each side = 1 blink
Front bags
Moomba
1) Outback V = 3 minutes of fill time = 3 blinks 2) LS / LSV = 3 minutes of fill time = 3 blinks 3) XLV = 4 minutes of fill time = 5 blinks
Supra
1) 20 SSV = 3 minutes of fill time = 3 blinks
2) 21V=4minutesoffilltime=5blinks
3) 22 SSV Walk-Thru = 3 minutes of fill time = 3 blinks 4) 22 SSV Play-pen = 4 minutes of fill time = 5 blinks 5) 24 SSV Walk-Thru = 3 minutes of fill time = 3 blinks 6) 24 SSV Play-pen = 11 minutes of fill time = 19 blinks
Sent from my iPad using Tapatalk HD
Attachment 17287
Sent from my iPad using Tapatalk HD
My boat requires the switch/blink trick.
Not hard to do after the first time.