Winterization for newer Raptor motors
I have a '16 Craz with the "standard" 400 engine and being a boat owner for many years I have always done my own winterization. Obviously this new motor uses a self contained coolant and a heat exchanger so it's different than any boat I have owned. I have read several threads that have suggested ideas. The owners manual is not much help. So I thought I would post what I have gathered and see if anyone has suggestions or improvements. The picture of the 5 critical drain plug points has been previously posted in pdf format.
Add Stabil fuel stabilizer to gas tank and fill tank
Remove 2 hull drain plugs and place in ziploc bag, tape to steering wheel
Pump out all ballast
Attach hose to water intake and run engine to operating temperature / 160 degrees
Drain oil, replace oil filter with Motorcraft FL-820 or Wix 51372
Fill oil with Semi Synthetic 5W-30 - 8 quarts
Remove 5 drain plugs from heat exchanger , manifolds and transmission ( see picture)
Clean and drain lake water strainer if equipped ( was an option)
Remove spark plugs and fog each cylinder with fogging oil, crank engine to spread fogging oil
Detach hoses from ballast pumps, pour in RV antifreeze, cycle pump to insure it runs through
Detach and remove ballast bags, add 1/4 cup bleach and slosh around
Plug in on board battery charger or remove a batteries and place on trickle charger
Every other year ? ( I have the Indmar V Drive unit )
Drain and refill V drive (yellow dipstick)and transmission ( red dipstick). I believe these fluids need to be sucked out with a vacuum pump and a small tube.
Trans takes 2.3 qts Indmar ATF 872006 ( Can use Dextron 6 synthetic)
V-Drive takes 1.25 qts Indmar Synthetic 50 Transmission oil 872009 ( can use Mobil Delvac 50 synthetiic transmission oil)
Replace lake water impeller
I welcome and constructive comments. Thank you.
Winterization for newer Raptor motors
Trayson, then you raptor engines are closed loop cooling system. That means they have anti-freeze just like your car. So we would not be pulling out the engine plugs, unless you were changing the coolant somewhere down the line.
Sent from my iPhone using Tapatalk
Winterization for newer Raptor motors
Quote:
Originally Posted by
DRHRSH
I have a '16 Craz with the "standard" 400 engine and being a boat owner for many years I have always done my own winterization. Obviously this new motor uses a self contained coolant and a heat exchanger so it's different than any boat I have owned. I have read several threads that have suggested ideas. The owners manual is not much help. So I thought I would post what I have gathered and see if anyone has suggestions or improvements. The picture of the 5 critical drain plug points has been previously posted in pdf format.
Add Stabil fuel stabilizer to gas tank and fill tank
Remove 2 hull drain plugs and place in ziploc bag, tape to steering wheel
Pump out all ballast
Attach hose to water intake and run engine to operating temperature / 160 degrees
Drain oil, replace oil filter with Motorcraft FL-820 or Wix 51372
Fill oil with Semi Synthetic 5W-30 - 8 quarts
Remove 5 drain plugs from heat exchanger , manifolds and transmission ( see picture)
Clean and drain lake water strainer if equipped ( was an option)
Remove spark plugs and fog each cylinder with fogging oil, crank engine to spread fogging oil
Detach hoses from ballast pumps, pour in RV antifreeze, cycle pump to insure it runs through
Detach and remove ballast bags, add 1/4 cup bleach and slosh around
Plug in on board battery charger or remove a batteries and place on trickle charger
Every other year ? ( I have the Indmar V Drive unit )
Drain and refill V drive (yellow dipstick)and transmission ( red dipstick). I believe these fluids need to be sucked out with a vacuum pump and a small tube.
Trans takes 2.3 qts Indmar ATF 872006 ( Can use Dextron 6 synthetic)
V-Drive takes 1.25 qts Indmar Synthetic 50 Transmission oil 872009 ( can use Mobil Delvac 50 synthetiic transmission oil)
Replace lake water impeller
I welcome and constructive comments. Thank you.
I had thought I removed 5 but realized today that I only removed 4. I have the 2 blue plastic wing nut looking plugs. One is from the manifold crossover. The 2nd is from the tube between the raw water pump and transmission cooler. The 3rd is the drain plug/anode from the heat exchanger. The 4th is the plug/ anode on the rear of the V drive.http://uploads.tapatalk-cdn.com/2016...767343861f.jpg
Which plug am I missing? My manual only indicates 4 plugs from my understanding. Thanks for the help!
Sent from my SM-G900W8 using Tapatalk