Heater installation 2020 Mojo

Since the end of summer is near us and my wife gets cold easily it’s time to install the heater.
I just ordered the kit https://www.bakesonline.com/heater-c...eater-kit.html
Now the challenge is going to be installation.
Im planning on mimicking the manufacturer set up including yawing hash switches.

Does anyone here have a cooling system diagram for the raptor engine? Or if you have a heater would you mind taking pictures to show where the supply and return is?
Also which switch on the dash is dedicated to the heater?


Sent from my iPhone using Tapatalk

I have a 2020 with the factory heater. I will take some pics and send them off to you.

When you open the engine hatch the heater lines will be on the back right if you're standing in the boat. There will be a little loop of heater hose, you'll remove that and then run your supply and return.

Attachment 30029

You will also need a circulation pump for the raptor motor:
https://www.wakemakers.com/heater-cr...rofit-kit.html

Quote:

---

Originally Posted by Tommy2slow

I have a 2020 with the factory heater. I will take some pics and send them off to you.

---

Thank you. Very much appreciated. I will try to document the entire install for anyone else to use.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by SONIC

When you open the engine hatch the heater lines will be on the back right if you're standing in the boat. There will be a little loop of heater hose, you'll remove that and then run your supply and return.

Attachment 30029

You will also need a circulation pump for the raptor motor:
https://www.wakemakers.com/heater-cr...rofit-kit.html

---

Thank you for the info. Can you tell me why would I need recirculating pump? Is it to improve the flow?


Sent from my iPhone using Tapatalk

The raptor motors don't have enough coolant flow through that circuit at low rpm without the pump, all of the factory installs have a circ pump.
Without it your heater will only be useful at higher rpm

My pumps toast and I can’t get one they’re all on back order or out of stock [emoji849]


Sent from my iPhone using Tapatalk

I just got a quote from Bakes.com. For the pump, 2 fittings and 1 harness…$405. That’s on top of $550 for the kit.
If it wasn’t for my wife I would choose cold. Lol [emoji38]


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Emilware

I just got a quote from Bakes.com. For the pump, 2 fittings and 1 harness…$405. That’s on top of $550 for the kit.
If it wasn’t for my wife I would choose cold. Lol [emoji38]


Sent from my iPhone using Tapatalk

---

That’s a really decent price considering that is close to the heater option price from SC.


Sent from my iPhone using Tapatalk

I should have it all this Wednesday so this will be a busy weekend. Lol

What’s really funny is that if you flip the tag for ACC switch is actually labeled Heater.

Stay tuned for pics and install video.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Tommy2slow

I have a 2020 with the factory heater. I will take some pics and send them off to you.

---

Hey [mention]Tommy2slow [/mention] would you mind posting pics of the motor hose connection and placement of the blower. Thanks in advance


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Emilware

Hey [mention]Tommy2slow [/mention] would you mind posting pics of the motor hose connection and placement of the blower. Thanks in advance


Sent from my iPhone using Tapatalk

---

Hi Emilware,

My engine has blue labels with “To Heater “ & “From Heater” at the hose connections. Hard to see in the pic as I couldn’t find an angle that both were visible. The blower and hot tubes have a plastic cover that does a nice job separating them from the under seat storage. Tried to get pics of the hose routing under the hot tubes but they aren’t great. Pic of the wiring shows the yellow wire on my motor is not used. Hope this helps.https://uploads.tapatalk-cdn.com/202...cb4229386f.jpg
https://uploads.tapatalk-cdn.com/202...eb9ed4ac6d.jpg
https://uploads.tapatalk-cdn.com/202...bcbb4521ab.jpg





https://uploads.tapatalk-cdn.com/202...4e192ac8f6.jpg

https://uploads.tapatalk-cdn.com/202...2f611526c8.jpg
https://uploads.tapatalk-cdn.com/202...1144e94b64.jpg
https://uploads.tapatalk-cdn.com/202...317e9de774.jpg
https://uploads.tapatalk-cdn.com/202...c8b8512094.jpg


Sent from my iPhone using Tapatalk

Thank you [mention]Tommy2slow [/mention] this is perfect.


Sent from my iPhone using Tapatalk

https://uploads.tapatalk-cdn.com/202...6aab33db9b.jpg
https://uploads.tapatalk-cdn.com/202...6a74d0a447.jpg

So I was able to complete the install of the heater Kit 200 pro which I bought for bakes online.com.
The entire install took about 4 hours. It uses the factory switches for the high and low fan.

Check out the installation video.

https://youtu.be/tJutNJfvfQI


Sent from my iPhone using Tapatalk

Looks great. Glad the installation went well. That’s a great spot to install the motor and hot tubes. I didn’t realize you had a 2021 as the thread title was 2020 but all is good. We live in the north so our heater is essential. My son is training for the Canadian Wakeboard Nationals next weekend. 59 degrees in the water and 38 degrees in the air today . I will be pulling the boat out of the lake for the season as soon as we get back from the tournament .

Are you not installing a shower pump for flow through the heater?

My understanding is the raptors do not produce enough pressure in the coolant system to circulate coolant to the heater core. My pump went out and I had to bypass it for the time being.

Not getting super warm air out of mine at the moment although the blower still works fine.

Either way…nice install. Super clean!


Sent from my iPhone using Tapatalk

https://uploads.tapatalk-cdn.com/202...15869e08ae.jpg


Sent from my iPhone using Tapatalk

Heater in full effect after today’s session!https://uploads.tapatalk-cdn.com/202...fe3f775485.jpg


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by eder10986

https://uploads.tapatalk-cdn.com/202...15869e08ae.jpg


Sent from my iPhone using Tapatalk

---

I had all the intentions for putting one in. As a matter of fact I ordered it from SC but still don’t have a ETA so I decided to try without. So far I have tested it and seems to do well. The engine temp seems to hold good and there is enough heat coming from it.

I do have a electric water pump for VW Jetta that will arrive Monday just as a back up. It’s $50 comparing to $205 from SC or $160 from heater craft.
If I need to install it will a quick job. My plan is to put it in the engine compartment.
I’ll do a video on it too.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Tommy2slow

Heater in full effect after today’s session!https://uploads.tapatalk-cdn.com/202...fe3f775485.jpg


Sent from my iPhone using Tapatalk

---

Dude. You are champ!!!
Looks like you guys are definitely getting your moneys worth out of it.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Emilware

I had all the intentions for putting one in. As a matter of fact I ordered it from SC but still don’t have a ETA so I decided to try without. So far I have tested it and seems to do well. The engine temp seems to hold good and there is enough heat coming from it.

I do have a electric water pump for VW Jetta that will arrive Monday just as a back up. It’s $50 comparing to $205 from SC or $160 from heater craft.
If I need to install it will a quick job. My plan is to put it in the engine compartment.
I’ll do a video on it too.


Sent from my iPhone using Tapatalk

---

Awesome!!! Can you message me the details of the water pump you might supplement with? I’m running into the same issues with getting a pump. I wouldn’t mind trying a different option!

Thanks!


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by eder10986

Awesome!!! Can you message me the details of the water pump you might supplement with? I’m running into the same issues with getting a pump. I wouldn’t mind trying a different option!

Thanks!


Sent from my iPhone using Tapatalk

---

Here is the one I ordered. I cannot tell you for sure that it’s going to fit but it should based on the research I’ve done.

BOXI Electric Auxiliary Water Pump Fit for 2009-2017 Volkswagen CC 3.6L V6 / 2006-2017 Volkswagen Passat 3.6L V6 / 2009-2010 Volkswagen Passat CC 3.6L V6 / OE# 1K0965561F 1K0965561B https://www.amazon.com/dp/B07Y1Q8F3V...CDHYHMZS99KC92


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Emilware

Here is the one I ordered. I cannot tell you for sure that it’s going to fit but it should based on the research I’ve done.

BOXI Electric Auxiliary Water Pump Fit for 2009-2017 Volkswagen CC 3.6L V6 / 2006-2017 Volkswagen Passat 3.6L V6 / 2009-2010 Volkswagen Passat CC 3.6L V6 / OE# 1K0965561F 1K0965561B https://www.amazon.com/dp/B07Y1Q8F3V...CDHYHMZS99KC92


Sent from my iPhone using Tapatalk

---

Perfect. Thanks! I’ll look Into it as well and might order one if it’ll work for me.


Sent from my iPhone using Tapatalk

Guys, I know this should be trivial, but the pump is supplying to the heater versus suction from the heater on the the return loop to the engine correct?


Sent from my iPad using Tapatalk

Quote:

---

Originally Posted by BigOrange

Guys, I know this should be trivial, but the pump is supplying to the heater versus suction from the heater on the the return loop to the engine correct?


Sent from my iPad using Tapatalk

---

Correct. The pump supplies increased flow to heater core from engine.


Sent from my iPhone using Tapatalk

This is a really helpful thread. I have 2 dumb questions.

1- how do you wire in the pump? Can the dash switch and fuse support it?
2- how much coolant do you need to add to the engine once you’ve plumbed it in?

Quote:

---

Originally Posted by Byezb

This is a really helpful thread. I have 2 dumb questions.

1- how do you wire in the pump? Can the dash switch and fuse support it?
2- how much coolant do you need to add to the engine once you’ve plumbed it in?

---

There is no dump question.

The dash toggle is a switch relay combo so with the 14awg wire it should be good for at least 20amp.
However the only thing that you wanna run off of the switch is the blower. The recirculation pump also known as auxiliary water pump needs to run the entire time that your engine is running.
Basing it on the past experience there’s probably a set of leads that you can easily connect to the same way as they found the leads for the blower. Otherwise I will run it off of one of the engine relays.
For your information 75% manufactures try to come in as their part so wire harnesses are the same whether you have all the options or you don’t.
I design Robotics automation and assembly systems for most of the car manufactures and I commonality is the key to keeping the cost down.

Now back to the topic. I didn’t measure exactly how much coolant I had to add but what I did was:
1. Topped off the coolant reservoir
2. I took a small funnel and I filled out the hoses going from the engine to the heater coil.
You have to be quick on reconnecting. [emoji23]
This prevented having bunch of air in the system and the hot coolant circulated within a minute or so.

Hope this answer your question

Btw, the entire install from beginning to the end took less than four hours and if I’m able to use the aftermarket pump the entire cost of the heater install will be less than $620 which is $340 less than OEM option.


Sent from my iPhone using Tapatalk

So finally the heater installation has been completed.
I have to report that everything thing works as expected.
The fan is operating from the toggle switches and the recirculating pump has been connected to the wire harness. This means that it will only turn o when the engine is running.
That was a great win in my book.

Kit link:
https://www.bakesonline.com/heater-c...RoCRBQQAvD_BwE

Pump link:

labwork Auxiliary Cooling Water Pump 1K0965561J Fit for VW Jetta Golf Audi A3 Passat https://www.amazon.com/dp/B07NL3X6WH...ing=UTF8&psc=1

Overall It took about 5hrs to install and total was under $600.
The install was so easy that I’m contemplating on adding a second one in the bow.

This was a great and on. We used our heaters yesterday. I could not be happier.


Sent from my iPhone using Tapatalk

Any chance you could post some pics on how you tied in the circulation pump (hose attachments etc) and how you wired it?

I know I still owed you a pic of how mine is wired and I didn’t forget. Going to boat tomorrow and was going to send pics but it looks like you figured it out!


Sent from my iPhone using Tapatalk

Unfortunately I’m not gonna be at the boat for a couple of days and I did forget to take pictures. However my auxiliary pump is installed on the feed side of the heater coil. This means that it pushes water into the coil. Unlike water pump which needs to be on the return side from heat exchanger.

As for the Wiring, there is a plug on the V drive side of the block with the label heater only.
I had to take that apart and use the male female connectors and pins one and two. If you test it with the meter you will see that even with the ignition on and the engine not running there’s no voltage but as soon as engine is running there is 14 V DC on pins one and two.


Sent from my iPhone using Tapatalk

Makes sense. Thanks!! I would definitely like to see your hose connections to the pump whenever you get a chance. I’m thinking about picking one up too.


Sent from my iPhone using Tapatalk

Any updates on pics brother?


Sent from my iPhone using Tapatalk

I’m sorry that it has taken me this long to get to it but I finally remember to make a video showing hose connection and routing. So here it’s is.

https://youtu.be/N2iHvhYtApI


Sent from my iPhone using Tapatalk

This is awesome thanks so much!!!


Sent from my iPhone using Tapatalk