Adding a second gas tank filler?

I was looking at the tank on our 2016 Mojo and noticed that the tank is blow molded to allow the second filler location on the port side of the boat. Has anyone ever done this? It looks like it should be relatively simple to add the filler, but I was wondering if there were some landmines I am not seeing that would prevent this? We want the filler on the port side since it would line up nicely with our tow vehicles, meaning that haul to Lake Powell wouldn't require us to turn the boat/truck around to fill one or the other, just pull forward.

Thanks,

Nate

Should work, Supras have two.


Sent from my iPhone using Tapatalk

Agreed, my Makai has 2 and it makes filling up so nice when it is on the trailer. It shouldn't be too tough. Looking at the pictures on line it appears the Kaiyen and Mondo do as well.

I've been thinking about doing this over the winter as the parts I can find online seem to be in the $100 range for the gas line and the outside filler.
our boat is like yours in that the tank is blow molded and capped off for it and know it was an option.

I've drilled in hulls before to add more drains/vents but for some reason I'm second guessing this one but I think it's due to the filler being in the middle of the metalflake and if I jack it up, that's a spensive gel repair.

I have looked into this and it looks to me that the biggest issue is that the starboard side fuel filling location is molded into the top deck of the boat giving it a flat surface where the rest of it is curved. The port side top deck has no such pre-molded location. You may be able to mount the fuel door on a curved surface, just may take trying to find the most flat surface. I have a 17 Mojo and would love to do this as well so if you pull it off be sure to post a How To thread.

I would worry about debris falling in the tank when drilling and clogging the fuel pump sock. Can’t get that out unless you empty the clean the tank.

However it may never become an issue if it sits on the bottom of the tank.


Sent from my iPhone using Tapatalk

Does the tank the Supras use have two filler necks on them or just one filler neck and they use a Y pipe to the two fuel filler lines? Either way, just run a Y pipe and connect both of your filler hoses to it. Don't mess with drilling the tank.

Something like this:

https://www.ebay.com/i/143626010387?...hoCCxwQAvD_BwE

would assume that most of the tanks are coming from a similar manufacturer. could be wrong.

our current 2020 boat has a blowmolded intake on each side so both fill sides are independent of each other until connected to the tank. sounds like this is the same as zog on his mojo.. there's a rubber cap over the non-used intake held on by a hose clamp on ours.

our old old supra had the y adapter similar to unstuck's post above.

Quote:

---

Originally Posted by UNSTUCK

Does the tank the Supras use have two filler necks on them or just one filler neck and they use a Y pipe to the two fuel filler lines? Either way, just run a Y pipe and connect both of your filler hoses to it. Don't mess with drilling the tank.

Something like this:

https://www.ebay.com/i/143626010387?...hoCCxwQAvD_BwE

---

My Supra SL has a filler in each corner of the tank. You can see it via the transmission hatch. I would assume all Supras are setup the same with two.

That will make the job even easier and one less part to buy. My Tige also has two fills molded into the tank. Likely they all come from the same source.

Is there a fitting on the gas tank or is it a slide-on to the rubber hose connected with a few SS clamps?

Granted not a moomba but i am with others that tanks are coming from only a couple suppliers.
Easy to connect. Worst part is the filler.
https://uploads.tapatalk-cdn.com/202...a21974123a.jpg

Quote:

---

Originally Posted by sandm

Granted not a moomba but i am with others that tanks are coming from only a couple suppliers.
Easy to connect. Worst part is the filler.
https://uploads.tapatalk-cdn.com/202...a21974123a.jpg

---

Good pic. What I thought. Got a project where you are pulling up the floor?

Quote:

---

Originally Posted by MJHSupra

Good pic. What I thought. Got a project where you are pulling up the floor?

---

current boat floor is on hinges. took me less than 20 seconds to pull it up and snap pic.