Tab Content
  • TXSurf4's Avatar
    08-15-2022, 03:29 PM
    TXSurf4 replied to a thread Becoming a boat owner in General Chat
    Congrats!!! Looks like a great build!! You should be good with the prop you spec'd. If you end up loading it up heavy and need more you can always...
    6 replies | 126 view(s)
  • TXSurf4's Avatar
    08-15-2022, 02:04 PM
    With your boat being on the water you would be better suited to use lead in that space IMO. You could fit 600# in the space you are talking about...
    11 replies | 183 view(s)
  • TXSurf4's Avatar
    08-13-2022, 06:42 PM
    TXSurf4 replied to a thread Ballast tubing size in General Chat
    No problem. Just so you know you will need a heat gun to get the hose on the fittings. So just make sure you have one before you start your...
    4 replies | 136 view(s)
  • TXSurf4's Avatar
    08-12-2022, 09:59 PM
    O they did. I just never noticed them until a month or so ago when I looked lol. I just got lucky there were on the correct sides. Sent from...
    109 replies | 4843 view(s)
  • TXSurf4's Avatar
    08-12-2022, 03:52 PM
    Interesting…….Check out the video on the Makai Explore page. It is about 30 seconds and says “In Floor Cooler”. Will be interesting to see if it...
    22 replies | 882 view(s)
  • TXSurf4's Avatar
    08-12-2022, 12:40 PM
    TXSurf4 replied to a thread Ballast tubing size in General Chat
    It is 1" tubing.
    4 replies | 136 view(s)
  • TXSurf4's Avatar
    08-12-2022, 12:27 PM
    Dash is interesting, I will have to see in person. Makai got an in floor cooler!
    22 replies | 882 view(s)
  • TXSurf4's Avatar
    08-02-2022, 10:33 AM
    TXSurf4 replied to a thread Trailer Hitch Locks in General Chat
    Here is the link to the one for our actual couplers as the link before was just to their selection of locks. ...
    18 replies | 501 view(s)
  • TXSurf4's Avatar
    08-02-2022, 01:06 AM
    TXSurf4 replied to a thread Trailer Hitch Locks in General Chat
    Don’t mean to ruffle any feathers with this one but both of those are not worth the $. The yellow one just needs a swift blow with a sledgehammer...
    18 replies | 501 view(s)
  • TXSurf4's Avatar
    08-01-2022, 08:16 AM
    No, unfortunately our lake is now 4' down and I had to pull the Makai off the lift and put it in the garage so that it didn't get stuck on the lift. ...
    109 replies | 4843 view(s)
  • TXSurf4's Avatar
    07-28-2022, 11:18 PM
    Ya no worries. I think you will notice a big difference. Hopefully you can get on the water and test it out. Let us know how it does. Also send...
    12 replies | 422 view(s)
  • TXSurf4's Avatar
    07-26-2022, 03:48 PM
    Never regretted getting a bigger boat or a bigger motor. I actually prefer the look of the SL over the SA. I like lines and the gel layout better...
    47 replies | 1544 view(s)
  • TXSurf4's Avatar
    07-26-2022, 01:00 PM
    TXSurf4 replied to a thread 2023 Moomba Models in General Chat
    So Supra went live with the 2023 stuff any predictions on how long until we see the Moomba 2023 update?
    61 replies | 3932 view(s)
  • TXSurf4's Avatar
    07-26-2022, 10:53 AM
    Ya I don't have any experience boating at elevation so I can't say how much that is affecting your issue. I can say that regardless of your altitude...
    12 replies | 422 view(s)
  • TXSurf4's Avatar
    07-25-2022, 12:53 PM
    TXSurf4 replied to a thread 2023 Supra Models in General Chat
    New SE lines and gel coat sections are done nicely. A definite improvement IMO. Looks like it got all the SL improvements as well as 4700# of...
    116 replies | 5472 view(s)
  • TXSurf4's Avatar
    07-25-2022, 10:12 AM
    Your prop is your issue. I am not sure why they have it listed as a "Surf Prop" bc the pitch wont get a slammed boat to surf speed or to hold that...
    12 replies | 422 view(s)
  • TXSurf4's Avatar
    07-25-2022, 07:47 AM
    Man that is a bummer to hear. I will have to keep an eye on my rears panels. I used WakeMakers Kit to reinforce mine engine dividers and actually...
    109 replies | 4843 view(s)
  • TXSurf4's Avatar
    07-20-2022, 11:11 PM
    couldn’t agree more I just find myself telling people to reference this or that and it is all his stuff lol Drink on my friend!! For me...
    66 replies | 3034 view(s)
  • TXSurf4's Avatar
    07-20-2022, 02:18 PM
    While I think we all agree that we want to keep our boats as heavy as possible while we surf I personally don't have the time or the patience to move...
    66 replies | 3034 view(s)
  • TXSurf4's Avatar
    07-20-2022, 08:40 AM
    TXSurf4 replied to a thread 2023 Supra Models in General Chat
    LMAO!!! Surprising we haven't seen a teaser yet. Last year the SL teaser was July 14th.
    116 replies | 5472 view(s)
  • TXSurf4's Avatar
    07-20-2022, 08:33 AM
    It don't believe it needs to be raised for the wake makers kit as the point of the kit is to increase your displacement which should increase your...
    66 replies | 3034 view(s)
No More Results
About TXSurf4

Basic Information

About TXSurf4
Location:
Hockley, Tx

Signature


2019 Makai
Raptor 450 w/ 1.76 Trans
WakeMakers 1350s in the rear & 1K in Lead

Statistics


Total Posts
Total Posts
993
Posts Per Day
0.71
General Information
Last Activity
Yesterday 02:12 PM
Join Date
10-25-2018
Referrals
0