Tab Content
  • jason1973's Avatar
    01-15-2019, 03:24 PM
    jason1973 replied to a thread Not happy in General Chat
    Something isn't right. I bought my boat from a dealer 2 hours from me and i have another dealer who i would NEVER buy from just 20 min away. I...
    43 replies | 952 view(s)
  • jason1973's Avatar
    01-11-2019, 09:45 PM
    Couldn't agree more. I was dead set on the axis until I looked at one and went thru it. And axis raised prices upward of 7% for 2019 for whatever...
    48 replies | 1362 view(s)
  • jason1973's Avatar
    01-10-2019, 04:21 PM
    i couldn't agree more. Let experts make the motor, lets expers make the boat. Same for most industries. When focused in too many areas, you lose...
    48 replies | 1362 view(s)
  • jason1973's Avatar
    01-10-2019, 03:53 PM
    Malibu is doing this for profit. I don't think they are afraid to say that either. I have seen some reps claim its so they can control quality etc......
    48 replies | 1362 view(s)
  • jason1973's Avatar
    01-10-2019, 11:51 AM
    Malibu announced a while back they are going to marinize their own engines starting in 2019. I hear they are available if you order, but i think...
    48 replies | 1362 view(s)
  • jason1973's Avatar
    01-09-2019, 02:12 PM
    Based on my findings, i would say 81k is good depending on options of course. But for a loaded Craz, i would take that.
    11 replies | 684 view(s)
  • jason1973's Avatar
    01-09-2019, 09:30 AM
    I will chime in, since i looked at every single boat on earth while searching for my new ride. I ended up ordering a new Mondo btw.. I looked heavily...
    11 replies | 684 view(s)
  • jason1973's Avatar
    01-04-2019, 09:57 PM
    jason1973 replied to a thread Boat lift help in General Chat
    When you say 18" on center I am assuming each bunk was 18" from the middle of the lift, making them basically 36" apart correct?
    8 replies | 766 view(s)
  • jason1973's Avatar
    01-04-2019, 05:15 PM
    jason1973 replied to a thread Boat lift help in General Chat
    With my X2 mastercraft, i never got close to hitting the shaft. The section of pier in front of my lift provided a reminder not to go to far. But...
    8 replies | 766 view(s)
  • jason1973's Avatar
    01-02-2019, 02:15 PM
    jason1973 started a thread Boat lift help in General Chat
    Need a little help, below is a pic of my current boat lift. Its a Floe. If you look at the center bunks, i have them sitting about 10" above the...
    8 replies | 766 view(s)
  • jason1973's Avatar
    12-24-2018, 09:44 AM
    jason1973 replied to a thread Shopping for a Craz in General Chat
    We boat in Wisconsin and NEVER once used the heaters. I do have them, but to be honest, i can take it or leave it. Not important to me. The most...
    32 replies | 1034 view(s)
No More Results
About jason1973

Basic Information

About jason1973
Location:
Ohio

Signature


2019 Mondo - no longer on order. Took delivery!

Statistics


Total Posts
Total Posts
67
Posts Per Day
0.08
General Information
Last Activity
01-15-2019 04:40 PM
Join Date
10-11-2016
Referrals
0