View Full Version : Where to buy a swim platform pin? *pic*
deafgoose
09-19-2010, 12:06 PM
One of the pins on my swim platform broke so now I need to order a new one.
I don't have any Moomba dealers nearby so I will order some online.
Where would I find these?
deafgoose
09-19-2010, 12:20 PM
I did a bit of reaeach and it seems people prefer the clevis pin instead.
Does it look like this?
http://upload.wikimedia.org/wikipedia/commons/6/63/Moused_shackle.gif
maxpower220
09-19-2010, 02:12 PM
You can find many of those type items at a hardware store.
Razzman
09-19-2010, 02:36 PM
Try McMaster-Carr (http://www.mcmaster.com/#pins/=8x17df), they have a big slection of various pins.
Deafgoose i've never seen anyone use a clevis to secure the platform. Most use a simple pin/clip method.
KSmith
09-19-2010, 03:35 PM
One of the pins on my swim platform broke so now I need to order a new one.
I don't have any Moomba dealers nearby so I will order some online.
Where would I find these?
One of these perhaps?
http://www.marinepartdepot.com/newststqurep.html
deafgoose
09-19-2010, 07:32 PM
One of these perhaps?
http://www.marinepartdepot.com/newststqurep.html
So close!
The pin I have is 2" long. The pin listed on the link above is 1.5" long.
deerfield
09-19-2010, 08:52 PM
One of the pins on my swim platform broke so now I need to order a new one.
I don't have any Moomba dealers nearby so I will order some online.
Where would I find these?
deaf - Ultimate Wake Watersports keeps inventory of these pins in its service shop. I stopped in today to chat and asked specifically about availability. It's a Moonba Supra dealer in the suburb of Volo north of Chicago. Store was open but shop was not, so I don't have a price for you. Give a call during the week and see what it would cost to buy and ship to you. - Deerfield
mnpracing
09-19-2010, 08:55 PM
Home improvement store will have a pin similar to the pin that holds the guidepoles on your trailer. Just need a 1/4in X 2. I switched to those because I don't trust the stock pins.
deafgoose
09-22-2010, 12:27 AM
I picked up two quick pins to replace the swivel lock pins but I am not sure how long they will last. They are made of grade 5 steel with a clear zinc plated finish.
I also got some adjustable clevis pins in case the quick pins don't fit.
I really wish these were stainless. The zinc coating will wear off and it will rust over time. Good thing they are only $1.30 each locally!
Zinc Plating
Many steel fasteners are electro-plated with zinc for better corrosion resistance. Fasteners that have been zinc plated have a shiny silver or golden appearance referred to as clear or yellow zinc respectively. They are fairly corrosion resistant but will rust if the coating is destroyed or if exposed to a marine environment.
VA LSV
09-22-2010, 06:13 AM
From an earlier post about platform rattle. Search can be your friend.
Took the brackets off my swim platform, welded up the holes, installed everything on the boat and drilled 5/16 holes through brackets & hangers so everything lined up. No more rattle. Used these pins.
http://www.grainger.com/Grainger/items/5VU22?Pid=search
deafgoose
09-22-2010, 11:38 AM
From an earlier post about platform rattle. Search can be your friend.
Took the brackets off my swim platform, welded up the holes, installed everything on the boat and drilled 5/16 holes through brackets & hangers so everything lined up. No more rattle. Used these pins.
http://www.grainger.com/Grainger/items/5VU22?Pid=search
Who said anything about rattles?
viking
09-22-2010, 11:46 AM
From an earlier post about platform rattle. Search can be your friend.
Took the brackets off my swim platform, welded up the holes, installed everything on the boat and drilled 5/16 holes through brackets & hangers so everything lined up. No more rattle. Used these pins.
http://www.grainger.com/Grainger/items/5VU22?Pid=search
I followed that thread as it was going on.
For purposes of my questions:
1.) Platform brackets attached to Platform - 1 hole each side
2.) Platform bracket hanger attached to the transom - 2 holes each side
3.) Platform bracket slides into platform bracket hangers and secured via pins
The one question I had about the solution - Did you weld up and re-drill just the holes on the Platform brackets or did you take the hangers off the boat too and weld/re-drill those?
Either way did you have to re-finish the metal with paint or what did you do there?
Thanx
VA LSV
09-22-2010, 12:11 PM
viking
Welded up the platform brackets only and painted with semi-gloss black. Original holes were 1/4" so 5/16" made sure all lined up.
deafgoose
Post contained a link to SS lock pins with an explination why they were 5/16 instead of 1/4. Searched platform+pins.
KSmith
09-30-2010, 07:35 AM
Who said anything about rattles?
You can't hear that? :shock:
papou
09-30-2010, 07:42 PM
deafgoose did you try Ottawa fastener supply on Robertson RD
that is ware i bye all my stainless screws,nuts and bolts.
deafgoose
09-30-2010, 10:10 PM
deafgoose did you try Ottawa fastener supply on Robertson RD
that is ware i bye all my stainless screws,nuts and bolts.
That is exactly where i got them. :D
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.