Activity Stream
-
Older Activity
-
03-09-2025, 11:06 PMI have a 2003 22ssv that I'm doing a full re-upholstery on. It is the first upholstery job for me but I have some experience with canvas work. It...9 replies | 7090 view(s) -
02-25-2025, 03:49 PMRead on social media today (and Drew announced it on his personal Facebook page), that he was leaving Skiers Choice and taking a Business Development...4 replies | 5901 view(s) -
02-25-2025, 04:57 PMMy worst nightmare. Battery got under water and of course is toast(fresh water btw) Boat will run for ~30 mins then heats up and dies. Marina says...5 replies | 5295 view(s)
-
03-17-2025, 12:44 PMI had to replace a brake line on my trailer over the weekend. I was pretty sure I got all the air out of the lines by manually bleeding the system. ...6 replies | 3866 view(s) -
Yesterday, 02:55 PM*sold* sold2 replies | 15875 view(s) -
03-23-2025, 07:15 PMAwesome. Thank you! Yes mine is smooth. Sent from my iPhone using Tapatalk21 replies | 5633 view(s)
-
03-23-2025, 03:37 PMThat was the part number I used for the pulley. I have a local-ish Indmar dealer that ordered both the pulley and the belt for me. Check...21 replies | 5633 view(s) -
03-23-2025, 08:44 AMWas the P/N the 551246? I am having the same problem trying to figure out the part number. I see that one on Inboard Online. Just want to make...21 replies | 5633 view(s)
-
03-21-2025, 09:58 PMThis the pulley that failed on me. The bearing seized and the belt ate the plastic.21 replies | 5633 view(s)
-
03-21-2025, 09:57 PMThe half inch drive goes in the square hole on the right. My ratchet did not give me enough leverage. I used a 24" breaker bar and it was easy.21 replies | 5633 view(s)
-
03-21-2025, 08:36 PMIt had a little wobble, so I was going to replace it while I have the belt off. Sent from my iPhone using Tapatalk21 replies | 5633 view(s)
-
03-21-2025, 08:34 PMHow do you loosen the belt tension? I saw online you put a 1/2” drive socket into the tensioner, but it doesn’t seem to move easily like the video I...21 replies | 5633 view(s)
-
03-20-2025, 11:52 AMYeah I wasn't excited about it at the time but it was an insurance job so... The other upholstery shops around were $500-1000 less but they would...9 replies | 7090 view(s) -
03-19-2025, 01:12 PMSounds good. We do the 3/2 shortie suits and make sure the driver does not keep us in the water too long on pick-ups and launches.46 replies | 46961 view(s)
-
03-18-2025, 08:54 PMHubs are good. Truth be told, I actually pulled all 4 to clean out and replace all the old hybrid grease and check bearings. That is how I broke...6 replies | 3866 view(s)
-
03-18-2025, 07:06 PMI would also make sure the temperature difference is not due to any low grease in the wheel bearing hubs. Unless they are sealed? Sent from my...6 replies | 3866 view(s) -
03-18-2025, 01:35 PMGot the first surf of the season in last week here in Houston. Kids braved the tube but wouldn't commit to board sports yet and wife wouldn't even...46 replies | 46961 view(s) -
03-18-2025, 12:27 PM65 degrees yesterday and 5 inches of snow today, Ugh!46 replies | 46961 view(s) -
03-18-2025, 09:49 AMGreat tip. And yes, I have an oil extractor. Didn’t even think about it. Sent from my iPhone using Tapatalk6 replies | 3866 view(s)
-
03-18-2025, 09:25 AMIf you have an oil extractor for your boat already just it. You can have someone putting fluid in as you pump the extractor. Next time anyone...6 replies | 3866 view(s)
-
03-18-2025, 09:19 AMYep. 3 bolts, hub on pump pulls back just enough to run the flat belt through. Bolt pump back to balancer. The bolts completely suck to remove. ...21 replies | 5633 view(s)
-
03-18-2025, 09:17 AMHello! Been a bit since I've been on here. So ready for summer. Weather staying in the 70s for the most part, water still low 50s. About to start my...46 replies | 46961 view(s) -
03-17-2025, 11:26 PMNo way I'd do it for that considering just the materials. I have probably 2 grand in materials not including any foam replacement.9 replies | 7090 view(s)
-
03-17-2025, 09:12 PMI know this is an old post, but I was going to replace my belt as normal maintenance. Are you able to explain a little more in depth as to how you...21 replies | 5633 view(s)
-
03-17-2025, 09:08 PMSent from my iPhone using Tapatalk21 replies | 5633 view(s)
-
03-17-2025, 06:57 PMYeah, I am thinking about buying one of those vacuum bleeders for $30 on Amazon. Sent from my iPhone using Tapatalk6 replies | 3866 view(s)
-
03-17-2025, 06:25 PM$5900 - full interior, lots of custom design/stitching and logo embroidery and new foam on most of the seats and entire rear sundeck (split it from a...9 replies | 7090 view(s)
-
03-17-2025, 06:17 PMI would suggest using a power bleeder just to be sure. Cheap insurance vs toasting an axle seal and available to borrow/rent from some auto parts...6 replies | 3866 view(s)
-
03-16-2025, 01:35 PM70 here on Friday 2" of snow today, love confused Wisconsin weather Sent from my iPad using Tapatalk46 replies | 46961 view(s)
